Abstract:The detonation spraying of coatings from fine composite materials is analyzed in the paper. The use of detonation coatings was found to improve the properties of machines and mechanisms and extend their life, while their functional performances are maintained over long-term operation. The structural features, strength, and fracture toughness of the coatings produced by multichamber detonation spraying from 75 wt.% Cr 3 C 2 + 25 wt.% NiCr and Ni–Cr–Fe–B–Si (77–81.5 wt.% Ni, 10–14 wt.% Cr, 5–7 wt.% Fe, 2.0–2.3 wt.% B, 2.0–3.2 wt.% Si, 0.5 wt.% C) powder materials were examined. Changes in the detonation spraying parameters were proved to significantly influence the structure of the coatings: microhardness, phase composition, volume content of lamellae, sizes of grains and subgrains, phase formation, and dislocation density. The structural and phase state of the coatings was studied at all structural levels using a comprehensive approach, involving light and scanning electron microscopy, X-ray diffraction, and transmission electron microscopy. The prospects of the multichamber detonation spraying method, ensuring the necessary combination of structural and phase parameters of the coating material with a simultaneous increase in their physical, mechanical, and operational properties, were demonstrated. A high level of strengthening and fracture toughness of the coatings was promoted by optimal structural and phase constituents: fine grain and subgrain structure, uniform distribution of nanosized strengthening particles, and uniform dislocation density. The improved fracture toughness of the coatings is due to the absence of extended structural areas of dislocation clusters. The gradient-free distribution of dislocation density prevents the formation of local internal stress concentrators in the resulting coatings.

Coating of diamond by thermal explosion reaction

The Microstructure of Al2O3/TiO2-NiCrBSi Graded Thermal Barrier Coatings Produced by Flame Spraying

Preparation of Ti-coated Diamond Particles by Microwave Heating

Unveiling the formation of Mo2C coating on diamond particles along with anisotropic etching by Mo powder

Compositionally graded multi-principal-element alloy coating with hybrid amorphous-nanocrystalline structure by directional electrical explosion

Microstructure and mechanism of Al2O3-ZrO2 eutectic coating prepared by combustion-assisted thermal explosion spraying

Diamond particles-reinforced Ni-based composite coating on Ti6Al4V alloy: Microstructure, mechanical, dynamic impact and dry-sliding tribological properties

Effect of Nitrogen Protective Atmosphere on Microstructure and High Temperature Erosion Property of TiAl3 and Cr3C2 Composite Coatings

Investigation of the Al-Mo-B(CN) Coatings Deposited Using Magnetron Sputtering of Al-Mo-B4C Target Produced by Detonation Spray Coating

Preparation of Diamond/aluminum Composite with Titanium Coating on Diamond Powder by Microwave Technology

Application of Raman Spectroscopy for Analyzing Diamond Coatings on a Hard Alloy

Growth and characterization of chemical vapor deposition diamond coating incorporated amorphous carbon with high Raman bands induced by CuO particles

Preparation and tribological properties of novel cold–sprayed Ti–diamond composite coating

A Novel Diamond/AlSi Composite Coating on Ti-6Al-4V SubStrate Made by Ultrasonic-Assisted Brazing

Nanoengineered Polycrystalline Diamond Composites with Advanced Wear Resistance and Thermal Stability

Microwave-Assisted Molten-Salt Facile Synthesis of Chromium Carbide (cr3c2) Coatings on the Diamond Particles

Effects of TiMoTa nano-crystalline interlayer on nucleation, adhesion and tribological behaviors of diamond coating

Structural Features of the Cr3C2–NiCr and Ni–Cr–Fe–B–Si Coatings Produced by Multichamber Detonation Spraying

Preparation of New Al Based Complex Bonded Diamond Composite

Characterization of Cr Coating Obtained on Micrometer-Scale Diamond Particles Prepared by Molten Salt Method

The Microstructure and Wear Properties of Diamond Composite Coatings on TC4 Made by Induction Brazing