Abstract:Summary Batch transportation of oil and water is a new transportation method in oil and gas gathering and transportation pipelines. Its corrosion inhibition effect has been preliminarily verified in a horizontal pipe experiment. However, achieving overall visualization in traditional loops is difficult, resulting in limited flow pattern classification and analysis of influencing factors. Combining the advantages of the traditional flow loop and the wheel flow loop, we introduce in this paper a round-head straight pipe loop and analyze the influence of key factors on the evolution of the flow pattern of the oil-water interface and the dimensionless length of the oil-water film (L~o, L~w) on the pipe wall through computational fluid dynamics (CFD) numerical simulation. The results show that the batch transportation of oil and water using the round-head straight pipe loop is more in line with the flow characteristics of oil and water two-phase flow in gathering pipelines. Three distinct three-layered flow patterns were identified, which are Flow Pattern I (oil-in-water in the upper layer, annular flow in the middle layer, and oil as the annular phase, water as the core phase, and oil-in-water in the lower layer, abbreviated as DW/O-AN-DW/O), Flow Pattern II (oil phase in the upper layer, annular flow in the middle layer, water as the annular phase, oil as the core phase, and oil in the lower layer, abbreviated as O-AN-O), and Flow Pattern III (oil phase in the upper layer, water-in-oil dispersion flow in the middle layer, and oil in the lower layer, abbreviated as O-DO/W-O). Additionally, parametric analysis reveals that the velocity of the rigid body (ν) has the greatest influence on the coverage rate of the oil film on the pipe wall, followed by the viscosity of crude oil. The density of crude oil has the least influence. The round-head straight pipe loop model offers an accurate simulation of the process of oil and water batch transportation in actual production pipelines. Therefore, the corrosion mitigation efficiency increases with the increase in oil viscosity when the viscosity of the oil lies within the range of 0.01–1 Pa·s. This increase is due to the formation of a more stable oil film on the pipe wall at higher viscosities. When the speed of the rigid body ranges from 0.5 to 1 m/s, due to the small fluid velocity, the erosion effect on the oil film on the pipe wall is relatively small, and the corrosion mitigation efficiency remains stable within a wide range.

Investigation of the Influence of Flow Pattern On the Internal Corrosion in Horizontal-Vertical Downward Pipe with Oil-Water Flow

Experimental and Numerical Analysis of the Impact of Corrosion on Pipeline Failure Pressure

Predicting Erosion-Corrosion Induced by the Interactions Between Multiphase Flow and Structure in Piping System

Surface Stress Analysis of Internally Corroded Pipes under External Pressure

Experimental investigation of oil–water flow in the horizontal and vertical sections of a continuous transportation pipe

Experimental investigation on flow patterns and pressure gradients of shale oil-water flow in a horizontal pipe

Experimental Investigation of Interfacial Wave in Stratified Low-Viscosity-oil and Water Flow in Horizontal and Upward Pipes

Investigation of corrosion sequence in the overhead pipeline of H2S stripper column through CFD models

Effect of the Y/T on the Burst Pressure for Corroded Pipelines with High Strength

Computational Fluid Dynamics Simulation of Oil-Water Batch Transport in a Pumpless Virtual Flow Loop

Corrosion Status of Oil Well Pipe and Anti-corrosion Technology Development

Double Circular Arc Model Based on Average Shear Stress Yield Criterion and Its Application in the Corroded Pipe Burst

The Flow Pattern Transition and Water Holdup of Gas–Liquid Flow in the Horizontal and Vertical Sections of a Continuous Transportation Pipe

Failure analysis and prediction of pipes due to the interaction between multiphase flow and structure

Experimental and numerical simulation of erosion-corrosion of 90° steel elbow in shale gas pipeline

Study on Flow Pattern Maps in Hilly-Terrain Air–water–oil Three-Phase Flows

Experimental Investigation of Oil-Water Two-Phase Flow in Horizontal, Inclined, and Vertical Large-Diameter Pipes: Determination of Flow Patterns, Holdup, and Pressure Drop

Investigation on Multiphase Erosion–Corrosion of Elbow in LPG Desulfurization Unit

CFD-Based Erosion and Corrosion Modeling of a Pipeline with CO2-Containing Gas–Water Two-Phase Flow

The Effect of Flowing Velocity and Impact Angle on the Fluid-Accelerated Corrosion of X65 Pipeline Steel in a Wet Gas Environment Containing CO2

Experimental and Theoretical Study of Interface Characteristics of Gas–Liquid Stratified Flow in Horizontal Pipe at High Pressure