Abstract:<section class="article-section__content"><p>Simultaneous high proton conductivity with high oxidative stability is one of the major concerns in the proton exchange membrane (PEM) preparation. With this perspective, different loadings of the sulfated zirconia‐titania, a binary metal oxide that possesses enhanced physicochemical properties, nanoparticle in sulfonated poly(ether ether ketone) (SPEEK) polymer were evaluated by the response surface method to obtain the novel PEM with boosted proton conductivity and oxidative stability. Two models for correlation of proton conductivity and oxidative stability (in Fenton solution) with two independent factors, including sulfonation time and the weight percent of the nanoparticle loading, were obtained by central composite design. The optimum parameters to attain the highest proton conductivity with oxidative stability are found to be the sulfonation time of 6.48 hours and the nanoparticle weight percent of 10.12%. The nanoparticle loading was found to be the more significant factor in the proton conductivity model, while the sulfonation time in the oxidative stability model was the main affecting factor. The optimal membranes were characterized by <sup>1</sup>H NMR, electrochemical impedance spectroscopy, Fenton test, Fourier transform infrared (FTIR), thermal gravimetric analysis (TGA), water uptake, swelling ratio, and atomic force microscopy (AFM) analysis. The results indicate that the introduction of the optimal contents of SZrTi nanoparticle into the polymer matrix would improve the water uptake and consequently the proton conductivity at a higher temperature while keeping the swelling ratio at an acceptable range. The highest achieved proton conductivity by the resulted nanocomposite was 29.21 mS cm<sup>−1</sup> at 120°C with 186‐minute durability in the Fenton's reagent. Moreover, the maximum peak power density of 199 mW cm<sup>−2</sup> was achieved at 90°C and 100% RH for the single‐cell performance test of nanocomposite‐based membrane electrode assembly (MEA), while it was recorded at 112 mW cm<sup>−2</sup> for commercial MEA. Acceptable dispersion of SZrTi nanoparticle in the SPEEK matrix causes negligible fuel crossover flux (eg, 0.35 × 10<sup>−6</sup> mmol s<sup>−1</sup> cm<sup>−2</sup> and 12.49 × 10<sup>−6</sup> mmol s<sup>−1</sup> cm<sup>−2</sup> for nanocomposite‐based MEA and commercial MEA, respectively), which is indispensable to improve the mechanical and chemical stability. So, the novel prepared nanocomposite SPEEK‐based membrane would be a promising alternative for the Nafion membrane at moderate to high temperatures. </p></section><section class="article-section__content"><h3 class="article-section__sub-title section1"> Highlights</h3><ul class="unordered-list"><li>Sulfated ZrO<sub>2</sub>‐TiO<sub>2</sub> binary oxide was introduced into the SPEEK polymer matrix. </li><li>Chemical stability and proton conductivity were promoted by design of experiments.</li><li>The nanoparticle loading was the main factor in the proton conductivity model.</li><li>Sulfonation time in the oxidative stability model was the most affecting factor.</li><li>Fuel crossover was omitted because of the presence of SZrTi nanoparticle in the SPEEK matrix.</li></ul></section>

Unveiling CeZnO x Bimetallic Oxide: A Promising Material to Develop Composite SPPO Membranes for Enhanced Oxidative Stability and Fuel Cell Performance

Ce–Mn bimetallic oxide-doped SPEEK/SPPO blend composite membranes to induce high oxidative tolerance and proton conductivity for hydrogen fuel cells

Highly Proton Conductive and Mechanically Robust SPEEK Composite Membranes Incorporated with Hierarchical Metal–organic Framework/carbon Nanotubes Compound

Boosting Antioxidation Efficiency of Nonstoichiometric CeOx Nanoparticles Via Surface Passivation Toward Robust Polymer Electrolyte Membrane Fuel Cells

Simultaneous improvement of ionic conductivity and oxidative stability of sulfonated poly(ether ether ketone) nanocomposite proton exchange membrane for fuel cell application

Improved Performance of Sulfonated Poly Ether Ether Ketone/three-Dimensional Hierarchical Molybdenum Disulfide Nanoflower Composite Proton Exchange Membrane for Fuel Cells

Titanium oxide/graphitic carbon nitride nanocomposites as fillers for enhancing the performance of SPAES membranes for fuel cells

Sulfonated poly(2,6-dimethyl-1,4-phenylene oxide) (SPPO) electrolyte membranes reinforced by electrospun nanofiber porous substrates for fuel cells

CeO2 stabilized by tourmaline as a novel inorganic filler to simultaneously increase the conductivity and durability of proton exchange membranes

A High-Strength Sm-doped CeO2 Oxide-Ion Conducting Electrolyte Membrane for Solid Oxide Fuel Cell Application

Enhanced Activities of Nano-Ceo2−δ@430l Composites by Zirconium Doping for Hydrogen Electro-Oxidation in Solid Oxide Fuel Cells

In Situ Polymerization-Mediated Cross-Linking of the MOF Using Poly(1-vinylimidazole) in SPEEK Fuel Cells

Novel bifunctional fillers (ATP/P–CNOs) for sulfonated poly(aryl ether sulfone) matrix for improved power output and durability of H2/O2 fuel cell at low humidity

Cerium Based Metal-Organic Framework As the Efficient Radical Quencher for Proton Exchange Membrane Fuel Cells

The Synthesis of Cerium Oxide Antioxidant Supported on Silica Nanotube for Polymer Electrolyte Membrane Fuel Cell

Fabrication and Performance of Pr-doped CeO2 Nanorods-Impregnated Sr-doped LaMnO3–Y2O3-stabilized ZrO2 Composite Cathodes for Intermediate Temperature Solid Oxide Fuel Cells

In Situ Symbiosis of Cerium Oxide Nanophase for Enhancing the Oxygen Electrocatalysis Performance of Single‐Atom Fe─N─C Catalyst with Prolonged Stability for Zinc–Air Batteries

Enhancing chemical stability and performance in proton-conducting solid oxide fuel cells through novel composite cathode design

Preparation and Characteristics of Pr<sub>1.2</sub>Sr<sub>0.8</sub>NiO<sub>4</sub>-Sm<sub>0.2</sub>Ce<sub>0.8</sub>O<sub>1.9</sub> Composite Powders for Solid Oxide Fuel Cell Cathode Applications

Incorporation of Ultralow Manganese Dioxide for Improving the Durability of Sulfonated Poly (ether Ether Ketone) Membranes in Passive Direct Methanol Fuel Cell

Design and Development of Copper Trimesic Acid Anchored sPEEK/Polyimide Composite Membranes for Fuel Cell Applications