Abstract:<section class="article-section__content"><p>Simultaneous high proton conductivity with high oxidative stability is one of the major concerns in the proton exchange membrane (PEM) preparation. With this perspective, different loadings of the sulfated zirconia‐titania, a binary metal oxide that possesses enhanced physicochemical properties, nanoparticle in sulfonated poly(ether ether ketone) (SPEEK) polymer were evaluated by the response surface method to obtain the novel PEM with boosted proton conductivity and oxidative stability. Two models for correlation of proton conductivity and oxidative stability (in Fenton solution) with two independent factors, including sulfonation time and the weight percent of the nanoparticle loading, were obtained by central composite design. The optimum parameters to attain the highest proton conductivity with oxidative stability are found to be the sulfonation time of 6.48 hours and the nanoparticle weight percent of 10.12%. The nanoparticle loading was found to be the more significant factor in the proton conductivity model, while the sulfonation time in the oxidative stability model was the main affecting factor. The optimal membranes were characterized by <sup>1</sup>H NMR, electrochemical impedance spectroscopy, Fenton test, Fourier transform infrared (FTIR), thermal gravimetric analysis (TGA), water uptake, swelling ratio, and atomic force microscopy (AFM) analysis. The results indicate that the introduction of the optimal contents of SZrTi nanoparticle into the polymer matrix would improve the water uptake and consequently the proton conductivity at a higher temperature while keeping the swelling ratio at an acceptable range. The highest achieved proton conductivity by the resulted nanocomposite was 29.21 mS cm<sup>−1</sup> at 120°C with 186‐minute durability in the Fenton's reagent. Moreover, the maximum peak power density of 199 mW cm<sup>−2</sup> was achieved at 90°C and 100% RH for the single‐cell performance test of nanocomposite‐based membrane electrode assembly (MEA), while it was recorded at 112 mW cm<sup>−2</sup> for commercial MEA. Acceptable dispersion of SZrTi nanoparticle in the SPEEK matrix causes negligible fuel crossover flux (eg, 0.35 × 10<sup>−6</sup> mmol s<sup>−1</sup> cm<sup>−2</sup> and 12.49 × 10<sup>−6</sup> mmol s<sup>−1</sup> cm<sup>−2</sup> for nanocomposite‐based MEA and commercial MEA, respectively), which is indispensable to improve the mechanical and chemical stability. So, the novel prepared nanocomposite SPEEK‐based membrane would be a promising alternative for the Nafion membrane at moderate to high temperatures. </p></section><section class="article-section__content"><h3 class="article-section__sub-title section1"> Highlights</h3><ul class="unordered-list"><li>Sulfated ZrO<sub>2</sub>‐TiO<sub>2</sub> binary oxide was introduced into the SPEEK polymer matrix. </li><li>Chemical stability and proton conductivity were promoted by design of experiments.</li><li>The nanoparticle loading was the main factor in the proton conductivity model.</li><li>Sulfonation time in the oxidative stability model was the most affecting factor.</li><li>Fuel crossover was omitted because of the presence of SZrTi nanoparticle in the SPEEK matrix.</li></ul></section>

Ce–Mn bimetallic oxide-doped SPEEK/SPPO blend composite membranes to induce high oxidative tolerance and proton conductivity for hydrogen fuel cells

Improved Performance of Sulfonated Poly Ether Ether Ketone/three-Dimensional Hierarchical Molybdenum Disulfide Nanoflower Composite Proton Exchange Membrane for Fuel Cells

Highly Proton Conductive and Mechanically Robust SPEEK Composite Membranes Incorporated with Hierarchical Metal–organic Framework/carbon Nanotubes Compound

Unveiling CeZnO x Bimetallic Oxide: A Promising Material to Develop Composite SPPO Membranes for Enhanced Oxidative Stability and Fuel Cell Performance

Mechanically Robust and Highly Methanol-Resistant Sulfonated Poly(ether Ether Ketone)/poly(vinylidene Fluoride) Nanofiber Composite Membranes for Direct Methanol Fuel Cells

Modification of sulfonated poly (etherether ketone) composite polymer electrolyte membranes with 2D molybdenum disulfide nanosheet-coated carbon nanotubes for direct methanol fuel cell application

Achieving Better Balance on the Mechanical Stability and Conduction Performance of Sulfonated Poly(ether Ether Ketone) Proton Exchange Membranes Through Polydopamine/polyethyleneimine Co-Modified Poly(vinylidene Fluoride) Nanofiber As Support

Design and Development of Copper Trimesic Acid Anchored sPEEK/Polyimide Composite Membranes for Fuel Cell Applications

PEMs with High Proton Conductivity and Excellent Methanol Resistance Based on Sulfonated Poly (aryl Ether Ketone Sulfone) Containing Comb-Shaped Structures for DMFCs Applications

Preparation and study on H–MoS 2 /SLS modified SPI@SPEEK blend proton exchange membrane with balanced proton conductivity and stability

Simultaneous improvement of ionic conductivity and oxidative stability of sulfonated poly(ether ether ketone) nanocomposite proton exchange membrane for fuel cell application

Development of sulfonic acid–functionalized tetraethyl orthosilicate derivative cross-linked with sulfonated PEEK membranes for fuel cell applications

SPEEK and SPPO Blended Membranes for Proton Exchange Membrane Fuel Cells

Incorporation of Ultralow Manganese Dioxide for Improving the Durability of Sulfonated Poly (ether Ether Ketone) Membranes in Passive Direct Methanol Fuel Cell

Ionically Crosslinked Composite Membranes from Polybenzimidazole and Sulfonated Poly (fluorenyl ether ketone) for High-Temperature PEM Fuel Cells

Friedel-Crafts self-crosslinking of sulfonated poly(etheretherketone) composite proton exchange membrane doped with phosphotungstic acid and carbon-based nanomaterials for fuel cell applications

In Situ Polymerization-Mediated Cross-Linking of the MOF Using Poly(1-vinylimidazole) in SPEEK Fuel Cells

SPEEK-co-PEK-x proton exchange membranes with controllable sulfonation degree for proton exchange membrane fuel cells

Polybenzimidazole/cerium dioxide/graphitic carbon nitride nanosheets for high performance and durable high temperature proton exchange membranes

Self-Assembly-Cooperating in Situ Construction of MXene–CeO 2 as Hybrid Membrane Coating for Durable and High-Performance Proton Exchange Membrane Fuel Cell

Multi-component organic/inorganic blend proton exchange membranes based on sulfonated poly(arylene ether sulfone)s for fuel cells