Abstract:Erosion of materials is one of the major causes that lead to the malfunction of equipment and facilities, and surface texturing can be a solution for enhancement of erosion resistance. In this work, superwetting (superhydrophilic/superhydrophobic) titanium (Ti) alloy surface with periodic microstructure was prepared by a facile laser-based surface texturing approach which combines laser surface texturing and low-temperature annealing. The effect of laser-induced surface texture and wettability on the erosion resistance of the laser textured surface was studied. Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) were used to analyze the chemical surface microstructure and surface on the untreated and laser textured surfaces. The hardness and contact angle of the untreated surface, superhydrophilic surface and superhydrophobic surface were measured by microhardness tester and contact angle goniometer. Using an in-house built erosion experimental setup, the erosion resistance of the untreated surface, superhydrophilic surface and superhydrophobic surface was investigated. The experimental results demonstrate that micro-bumps are formed after laser surface texturing. In the meantime, the surface hardness for the laser textured surface with a step size of 150 μm is increased by 48% under the load of 1.961 N. Compared with the untreated surface, the erosion resistance is increased by 33.9%, 23.8% and 16.1%, respectively, for the superhydrophobic surface. The SEM results show that the untreated surface has large and deep impact pits, while the superhydrophobic surface only has small and shallow impact pits, indicating that the erosion process resulted in less damage to the substrate. The EDS results shows that superhydrophobicity plays a critical role in protecting the substrate from erosion. It is thus believed that the superhydrophobic surface has pronounced effects for improving the hardness and erosion resistance of Ti alloy.

Assessment of Mechanical and Slurry Erosive Behavior on Laser-Textured Stainless Steel (SS410)

Wettability and Surface Roughness Analysis of Laser Surface Texturing of AISI 430 Stainless Steel

Time-dependent wetting behavior of the micro-textured stainless steel 316L using the mechanical indentation method

Realizing the tribological feasibility of novel laser surface texturing techniques for cold spray kinetically metallized stainless steel

Effect of Different Geometric Texture Shapes on Wettability and Machining Performance Evaluation Under Dry and MQL Environments

Friction and Wear Behavior of 316L Stainless Steel with Laser Micro-Hole Texture and Micro-Square-Column Array Texture

Morphological Analysis of Laser Surface Texturing Effect on AISI 430 Stainless Steel

Laser Texturing for Superwetting Titanium Alloy and Investigation of Its Erosion Resistance

Improved tribological performance of AISI 316L stainless steel by a combined surface treatment: Surface texturing by selective laser melting and plasma nitriding

A Study on Surface Topography in Cavitation Erosion Tests of AlSi10Mg

Laser Surface Texturing of Stainless Steel − Effect of Pulse Duration on Texture's Morphology and Frictional Response

Effect of Ultrasonic Cleaning after Laser Texturizing of Surface of AISI 316L Steel on the Degree of Wetting and Corrosion Resistance

Correlation between surface textural parameter and tribological behaviour of four metal materials with laser surface texturing (LST)

Surface Texturing for Low Friction Mechanical Components

Tribological behavior investigation of 316L stainless steel samples processed by selective laser melting

Effect of Nanosecond Laser Texturization on Tribological Behavior of AISI 321 Stainless Steel

Anti-Wear Property of Laser Textured 42CrMo Steel Surface

Characterization of a Laser Surface-Treated Martensitic Stainless Steel

Effect of Acid Erosion on the Tribological Performance of 304 Stainless Steel Surface Subjected to Liquid-Assisted Laser Texturing

Implementation of different scanning strategy to improve the mechanical and wear properties of 15-5 PH stainless steel fabricated by laser-directed energy deposition

Application of Taguchi Method Design to Investigate Tribological Performance of Laser-Surface-Textured 316L Austenitic Stainless Steel