Abstract:Mid-rise to tall mass timber buildings are becoming internationally popular and are required, for instance in the Eurocode or the Australian building code, to be designed against progressive collapse. Designing against progressive collapse is especially important for mass timber buildings as, when compared to reinforced concrete and steel, timber is a more brittle construction material and mass timber buildings are deemed to be more elastic and have limited rotational capacities at the beam-to-column connections. However, whilst the ability of reinforced concrete and steel buildings to resist such an extreme event has been widely researched, limited studies were carried out on mass timber buildings. Their load transfer mechanisms and structural response after the loss of a load-bearing element are currently unclear. Consequently, this paper presents the outcomes of three experimental tests performed on three scaled-down, 2 × 2-bay, post-and-beam mass timber substructures under an edge column removal scenario. The capacity of the 3D substructures to resist progressive collapse was investigated for two types of beam-to-column connectors, namely two tests performed with a connector type commonly used in Australia in mass timber buildings and one test with a proposed novel connector. In the tests, Uniformly Distributed Pressures (UDP) were applied to the floors in two stages: (i) a constant UDP of 4.8 kPa was first applied to the bays not adjacent to the removed column and (ii) an idealised UDP was then increasingly applied to the remaining two bays through a hydraulic jack connected to a six-point loading tree. The load redistribution mechanisms or alternative load paths, structural response and failure modes were recorded and are presented in this paper. Results showed that the applied load was principally transferred to the three columns closest to the removed column and that the Cross Laminated Timber (CLT) panels spanning over two bays were efficient in resisting and transferring the load. The substructure with the proposed novel connector showed an 8.5% increase in capacity and higher ductility than the substructures assembled with the commonly used connector. A simplified theoretical model consistent with the methodology currently used by industry to predict the collapse resistance capacity of post-and-beam mass timber buildings was compared to the test results. The model underpredicted the test capacity by 53%.

Compressive behavior of damaged timber columns: Experimental tests, degradation model, and repair method

Experimental Studies on Glubam Columns under Axial Compression

Axial Compression Behaviour of Bamboo-Wood Composite Columns Fabricated with Glubam and Laminated Veneer Lumber

An Experimental Study of Composite Columns Filled with Eucalyptus nitens Timber under Axial Compression

Experimental and Numerical Study of 7A04-T6 Extruded Aluminium Alloy Lipped Angle Columns in Axial Compression

A fiber beam-column model for damage assessment of traditional Chinese timber structures

Axial Loading Capacity Of Concrete-Jacketed Rc Columns With Pre- And Post-Corrosion Damage

EXPERIMENTAL STUDY ON AXIAL COMPRESSIVE BEHAVIOR OF TIMBER COLUMN LATERALLY STRENGTHENED WITH FRP

Analytical Model for Concrete Jacketed RC Columns with Precorrosion and Postcorrosion Damages under Uniaxial Loading

Mechanical Degradation of Reinforced Concrete Columns Corroded Under Sustained Loads

Mechanical behavior of laminated bamboo–timber composite columns under axial compression

Calculation of axial compressive behavior of timber column laterally strengthened with FRP

Performance degradation by column foot damage: From column foot joints to frames

Axial compressive behavior of pre-damaged concrete-filled square steel tube columns repaired with section circularization and CFRP composites

Compressive Behaviour of Corroded Thin-Walled Circular Section Steel Stub Columns

Experimental study on the compression behavior of long timber column strengthened with the novel hybrid fiber sheets

Experimental Study on Timber Columns Strengthened by CFRP Subjected to Axial Compression

Experimental study on the quasi-static progressive collapse response of post-and-beam mass timber buildings under an edge column removal scenario

Cracking Behavior of Cfrp Laminate-Strengthened Rc Beams with Premechanical and Postmechanical Environmental Damage

Residual Compressive Behaviour and CFRP Strengthening of SRCFST Columns after Combined Damage of Fire and Lateral Impact

EXPERIMENTAL STUDIES OF GLUBAM COLUMNS UNDER AXIAL LOADS