Abstract:Introduction The future of the international accord on mitigating the impact of climate change is linked to the successful commercialisation and implementation of renewable energy technologies. The latter is strongly dependent on finding commercially viable methods for successful dimensional nano-functionalization of the ceramic materials utilized in the fabrication of various energy devices either in energy generation (fuel cells) or storage (batteries, supercapacitors). Inkjet printing digital methods combining scalability and low equipment cost with high-resolution patterning can be a feasible solution for some of the shortcommings of the conventional fabrication technologies. 3D functionalization - Composite solid oxide fuel cells LSCF/CGO cathodes were nano-engineered via “dual” inkjet printing infiltration. The nano-decorated microstructure was found to extend the active three-phase boundary and to promote adsorbtion – dissociation - surface exchange reactions. Composite La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ /Ce 0.9 Gd 0.1 O 1.9 cathodes were subjected to “dual” inkjet printing infiltration of nitrate salt solutions in a single step procedure. After calcination in air at 700 o C the cathodes were decorated with Ce 0.9 Gd 0.1 O 1.9 and Co x O y nano particles. The effects of as created nano-decoration on the electrochemical activity and the performance stabilty in the intermediate temperature range (500-700 o C) were investigated. The infiltration was found to extend the active three-phase boundary and to promote adsorbtion-dissociation- surface exchange reactions. Electrochemical impedance tests conducted on symmetrical cells showed a reduction in the polarisation resistance of between 1.5 and 7.0 times depending on temperature (500-700 o C). The nano-decoration led to substantially enhanced stability (0.7 Ω•cm 2 at 550 o C after 100 hours of aging for CGO:Co x O y infiltration). As the composite LSCF/CGO cathodes had already percolating ionic and electronic networks, a low level loading of nanoparticles was sufficient to lead to an efficient short-range extension of the TPB and the density of ORR reaction sites. The sequence of infiltration was shown to influence the efficiency of the ORR promotion. Co x O y :CGO infiltration expanded the available surface area and promoted the catalytical activity towards ORR reaction. The superior effect of CGO:Co x O y infiltration was assigned to the introduction of additional promotion mechanisms (see Fig. 1) resulting in better electrochemical performance at lower temperatures (<650 o C). Both infiltrations suppressed the Sr surface segregation but only CGO:Co x O y infiltrated cathodes showed substantially improved stability after 100 hours of aging. Scaling up - Single step inkjet printing infiltration with doped ceria Ce 0.9 Ye 0.1 O 1.95 (YDC) and cobalt oxide (Co x O y ) precursor inks was performed in order scale-up the modification of the doped ceria interlayer in commercial (50x50x1 mm size) anode supported SOFCs. The penetration of the inks through the mono-phase La 0.8 Sr 0.2 Co 0.5 Fe 0.5 O 3-δ porous cathode to the Gd 0.1 Ce 0.9 O 2 interlayer was achieved by optimization of inks rheology jetting parameters. The low temperature calcination resulted in densification of the Gd-doped ceria porous interlayer as well as decoration of the cathode scaffold with nano-particles (~ 20-50 nm in size). The I-V testing in pure hydrogen showed maximum power density gain of 20% at 700 o C and 97% at 800 o C for the infiltrated cells (see Fig. 1). The effect was largely assigned to the improvement in the interfacial Ohmic resistance. The EIS study of the polarization losses of the reference and the infiltrated cells revealed reduction in the activation and concentration polarizations losses at 700 o C due to the nano-decoration of the La 0.8 Sr 0.2 Co 0.5 Fe 0.5 O 3-δ scaffold surface. Such effect was not clearly detectable at 800 o C where the drop of Ohmic losses was dominant. This work demonstrated that single-step inkjet printing infiltration, a non-disruptive low-cost technique, could produce significant and scalable performance enhancements in commercial SOFCs. Figure 1

University of Birmingham Formulation of Spinel based Inkjet Inks for Protective Layer Coatings in SOFC Interconnects

Formulation of spinel based inkjet inks for protective layer coatings in SOFC interconnects

Nano-Functionalization of SOFC Electrodes Via Inkjet Printing

Additive manufacturing of thin electrolyte layers via inkjet printing of highly-stable ceramic inks

Review—(Mn,Co)3O4-Based Spinels for SOFC Interconnect Coating Application

Development and Application of HVOF Sprayed Spinel Protective Coating for SOFC Interconnects

Aerosol Jet Printing and Microstructure of SOFC Electrolyte and Cathode Layers

The electrical property of MnCo2O4 and its application for SUS 430 metallic interconnect

Cu doped Mn-Co spinel protective coating on ferritic stainless steels for SOFC interconnect applications

Evaluating Ink Structure Using Ultrasonic Spray Coating for PEMFC MEA

Protective/Conductive Coatings on Ferritic Stainless Steels for Solid Oxide Fuel Cell Interconnect Applications

Protective coating based on manganese–copper oxide for solid oxide fuel cell interconnects: Plasma spray coating and performance evaluation

Effective post-processing strategies of inkjet-printed ceramic cathodes for improved fuel cell performance

Mn–Co spinel protective–conductive coating on AL453 ferritic stainless steel for IT-SOFC interconnect applications

Highly dense (Mn,Co)3O4 spinel protective coating derived from Mn–Co metal precursors for SOFC interconnect applications

Optimization of Hybrid Ink Formulation and IPL Sintering Process for Ink-Jet 3D Printing

Thermal Growth and Performance of Manganese Cobaltite Spinel Protection Layers on Ferritic Stainless Steel SOFC Interconnects

Inkjet printing additively manufactured multilayer SOFCs using high quality ceramic inks for performance enhancement

Research Progresses in the Preparation of Spinel Coatings on the Surface of SOFC Ferrite Stainless Steel Interconnectors

Supersonic spray derived Cu–Co oxide coating on SUS441 to protect the metallic interconnect and to increase stability of SOFC cathode

Optimization of the sintering thermal treatment and the ceramic ink used in direct ink writing of α-Al2O3: Characterization and catalytic application