Abstract:Introduction The future of the international accord on mitigating the impact of climate change is linked to the successful commercialisation and implementation of renewable energy technologies. The latter is strongly dependent on finding commercially viable methods for successful dimensional nano-functionalization of the ceramic materials utilized in the fabrication of various energy devices either in energy generation (fuel cells) or storage (batteries, supercapacitors). Inkjet printing digital methods combining scalability and low equipment cost with high-resolution patterning can be a feasible solution for some of the shortcommings of the conventional fabrication technologies. 3D functionalization - Composite solid oxide fuel cells LSCF/CGO cathodes were nano-engineered via “dual” inkjet printing infiltration. The nano-decorated microstructure was found to extend the active three-phase boundary and to promote adsorbtion – dissociation - surface exchange reactions. Composite La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ /Ce 0.9 Gd 0.1 O 1.9 cathodes were subjected to “dual” inkjet printing infiltration of nitrate salt solutions in a single step procedure. After calcination in air at 700 o C the cathodes were decorated with Ce 0.9 Gd 0.1 O 1.9 and Co x O y nano particles. The effects of as created nano-decoration on the electrochemical activity and the performance stabilty in the intermediate temperature range (500-700 o C) were investigated. The infiltration was found to extend the active three-phase boundary and to promote adsorbtion-dissociation- surface exchange reactions. Electrochemical impedance tests conducted on symmetrical cells showed a reduction in the polarisation resistance of between 1.5 and 7.0 times depending on temperature (500-700 o C). The nano-decoration led to substantially enhanced stability (0.7 Ω•cm 2 at 550 o C after 100 hours of aging for CGO:Co x O y infiltration). As the composite LSCF/CGO cathodes had already percolating ionic and electronic networks, a low level loading of nanoparticles was sufficient to lead to an efficient short-range extension of the TPB and the density of ORR reaction sites. The sequence of infiltration was shown to influence the efficiency of the ORR promotion. Co x O y :CGO infiltration expanded the available surface area and promoted the catalytical activity towards ORR reaction. The superior effect of CGO:Co x O y infiltration was assigned to the introduction of additional promotion mechanisms (see Fig. 1) resulting in better electrochemical performance at lower temperatures (<650 o C). Both infiltrations suppressed the Sr surface segregation but only CGO:Co x O y infiltrated cathodes showed substantially improved stability after 100 hours of aging. Scaling up - Single step inkjet printing infiltration with doped ceria Ce 0.9 Ye 0.1 O 1.95 (YDC) and cobalt oxide (Co x O y ) precursor inks was performed in order scale-up the modification of the doped ceria interlayer in commercial (50x50x1 mm size) anode supported SOFCs. The penetration of the inks through the mono-phase La 0.8 Sr 0.2 Co 0.5 Fe 0.5 O 3-δ porous cathode to the Gd 0.1 Ce 0.9 O 2 interlayer was achieved by optimization of inks rheology jetting parameters. The low temperature calcination resulted in densification of the Gd-doped ceria porous interlayer as well as decoration of the cathode scaffold with nano-particles (~ 20-50 nm in size). The I-V testing in pure hydrogen showed maximum power density gain of 20% at 700 o C and 97% at 800 o C for the infiltrated cells (see Fig. 1). The effect was largely assigned to the improvement in the interfacial Ohmic resistance. The EIS study of the polarization losses of the reference and the infiltrated cells revealed reduction in the activation and concentration polarizations losses at 700 o C due to the nano-decoration of the La 0.8 Sr 0.2 Co 0.5 Fe 0.5 O 3-δ scaffold surface. Such effect was not clearly detectable at 800 o C where the drop of Ohmic losses was dominant. This work demonstrated that single-step inkjet printing infiltration, a non-disruptive low-cost technique, could produce significant and scalable performance enhancements in commercial SOFCs. Figure 1

Inkjet printing additively manufactured multilayer SOFCs using high quality ceramic inks for performance enhancement

Low-temperature Solid Oxide Fuel Cells with Novel La0.6Sr0.4Co0.8Cu0.2O3−δ Perovskite Cathode and Functional Graded Anode

Additive manufacturing of thin electrolyte layers via inkjet printing of highly-stable ceramic inks

Nano-Functionalization of SOFC Electrodes Via Inkjet Printing

Effective post-processing strategies of inkjet-printed ceramic cathodes for improved fuel cell performance

Aerosol Jet Printing and Microstructure of SOFC Electrolyte and Cathode Layers

Three-Dimensional-Printed Composite Structures: The Effect of LSCF Slurry Solid Loading, Binder, and Direct-Write Process Parameters

Performance and Stability Analysis of SOFC Containing Thin and Dense Gadolinium-Doped Ceria Interlayer Sintered at Low Temperature

Inkjet-Printed LSM-YSZ Thin Films for Enhanced Oxygen Electrodes in Solid Oxide Fuel Cells

In Situ Densification of Gadolinium-Doped Ceria Interlayer by Infiltration Process in SOFC

Solid Oxide Fuel Cells with 3D Inkjet Printing Modified LSM-YSZ Interface

Formulation of spinel based inkjet inks for protective layer coatings in SOFC interconnects

An Anode-Supported Solid Oxide Fuel Cell (SOFC) Half-Cell Fabricated by Hybrid 3D Inkjet Printing and Laser Treatment

Sintered powder-base cathode over vacuum-deposited thin-film electrolyte of low-temperature solid oxide fuel cell: Performance and stability

Scalable and facile fabrication of tri-layer electrolytes by reactive sputtering for efficient and durable solid oxide fuel cells

Durability Study of Anode-Supported SOFC with Large-Area Fabricated By 4-Layer Sequential Co-Lamination and GDC Co-Firing Process

A new and simple way to prepare monolithic solid oxide fuel cell stack by stereolithography 3D printing technology using 8 mol% yttria stabilized zirconia photocurable slurry

Electrolyte-supported solid oxide fuel cells with ultra-thin honeycomb structure prepared by digital light processing 3D printing technology

Boosting intermediate temperature performance of solid oxide fuel cells via a tri‐layer ceria–zirconia–ceria electrolyte

Development of Graphene Oxide/Polyaniline Inks for High Performance Flexible Microsupercapacitors via Extrusion Printing

Highly dense and ultrathin gadolinia-doped ceria interlayer for enhanced performance of large-area anode-supported solid oxide fuel cell