Abstract:The Ni-Mn-based shape memory alloys as a promising candidate of elastocaloric material has been reported in many literatures, especially on bulk samples. The as-spun ribbon, which has a larger surface area and is more efficient for heat transfer, is rarely studied and hence of importance. In the present work, we succeeded in producing very long as-spun Ni-Fe-Mn-(Al, In) ribbons, with around 300 mm in length. The microstructure and mechanical properties of these as-spun ribbons were thoroughly investigated by scanning electron microscopy / electron backscattered diffraction (SEM/EBSD), nanoindentation and 3-points bending experiments. Through SEM/EBSD analyses, the microstructure and texture of the as-spun ribbons were studied. A gradient in microstructure exists along the thickness direction (TD) of the ribbon, which is induced by the temperature gradient during fast rate solidification, resulting in fine equiaxed grains along the surface contacted with the rotating wheel in melt spinning process and elongated grains, respectively. Both equiaxed and elongated grains possess a strong {001} fiber texture (<001>//TD). Nanoindentation analyses show little variation of hardness between the two different microstructures. The ductility index of both Ni-Fe-Mn-Al and Ni-Fe-Mn-In ribbons are within the range of intermetallic materials. The substitution of In by Al allows to increase very slightly the ductility index, which can reach 0.75. The fine equiaxed grains show better tensile resistance than the elongated grains in 3-points bending test. The substitution of In by Al improves the maximum bending strain by a factor of 3. The maximum strain for Ni-Fe-Mn-Al as-spun ribbons can reach 3 % before fracture. Fractography shows that the intergranular fracture is the main damage mechanism in these as-spun ribbons.

Structure, Phase Composition and Defect Substructure of High-Entropy Alloy Ribbon

MICROSTRUCTURE OF AS-MELT SPUN Al-Cu-Mg-Fe-Ni ALLOY AND ITS VARIATION IN CONTINUOUS HEAT TREATMENT

Structure and Properties of a Ribbon from FeCoNiSiB High-Entropy Alloy

Amorphous-crystalline Dual-Layer Structures Resulting from Metastable Liquid Phase Separation In(fe 50 Co 25 B 15 Si 10 ) 80 Cu 20 Melt-Spun Ribbons

Structure and Crystal Growth in Melt-Spun Fe81Ga19 Alloys

Phase structure and magnetostriction of Fe81Ga19 melt-spun ribbons

Studies of Structure Evolution of Nanostructured Hf11ni89 Alloy

Structures and Magnetic Properties of the Co7Hf Melt-Spun Ribbons

Microstructure and correlated mechanical properties study of Ni-(Fe, Co)-Mn-(Al, In) as-spun ribbons

Microstructure characterization and phase evolution of equiatomic AlCoMoFeNi high entropy alloy synthesized by mechanical alloying

Microstructures of Melt-Spun Cu100−x–Crx (x=3.4–25) Ribbons

Structure, thermodynamic behavior and static magnetic properties of Al addition FeCoNbCuB alloy ribbons

The Magnetic and Microstructural Evolution of Ni45mn24ga23co4cu4 Heusler Alloy Ribbons

Comparative study on the structure and magnetic properties of Sm10Co60Fe15(Al, B)15 amorphous-nanocrystalline ribbons

Microstructure and Phase Composition of the Cr-Mn-Fe-Co-Ni High-Entropy Alloy Obtained by Wire-Arc Additive Manufacturing

Research on Phases and Morphology of Sm<sub>2</sub>Fe<sub>17</sub> Melt-Spun Ribbon

Deformation and Fracture of High Entropy AlCoCrFeNi Alloy

On the Effect of the Melt Cooling Rate upon Spinning on the Structure of the Surface Layers of Fe77Ni1Si9B13 Alloy Ribbons

Magnetic and structural study of melt-spun YCo5 ribbons

Study On Structure And Magnetic Properties Of Y-2(Fe, Co)(14)B Melt-Spun Ribbons

Magnetic hardening in amorphous alloy Sm60Fe30Al10