Abstract:Mg–1Mn alloy, extruded at a low temperature in our published protocol, contributed to the intensified basal texture and extremely refined microstructure with spheroidal nanoscale precipitates dispersing throughout the matrix and along the grain boundaries, consequently resulting in the excellent mechanical properties where the alloy exhibited a tensile yield strength of 204.3 MPa and a ductility of 38.8% at room temperature. Therefore, Mg–1Mn alloy was recommended as one of the potential materials for structural applications. In the present investigation, hot deformation behavior through constitutive analysis and extrusion temperature-dependent microstructure, texture and mechanical properties of as-extruded Mg–1Mn alloy were investigated, aiming at revealing how extrusion temperature affected microstructure, texture, and mechanical properties of as-extruded Mg–1Mn alloy. X-ray diffraction patterns demonstrated that phase components of the experimental alloys consisted of the α-Mg matrix and Mn precipitates. Optical microscopy images indicated a significant increase in average grain size of the alloys as the extrusion temperature increasing from 250 °C to 400 °C. Scanning electron microscopy graphics revealed that coarsened particles identified as Mn precipitates by EDS were observed within the matrix when extrusion temperature reached 400 °C. Inverse pole figure maps of the experimental samples subjected to different extrusion temperatures in the present work exhibited the typical basal texture, suggesting that basal slip was activated hardly during the tensile stress applied along the extrusion direction. Consequently, extrusion temperature displayed the significant impact on microstructure, texture, and mechanical properties of as-extruded Mg–1Mn alloy. The alloy extruded at both 250 °C and 300 °C exhibited the strong basal texture and refined microstructure with spheroidal nanoscale precipitates dispersing within the matrix and along the grain boundaries, which contributed to their excellent comprehensive mechanical properties. The alloy extruded at 400 °C possessed the typical basal texture and coarsened microstructure, leading to the extremely poor mechanical properties. Simultaneously, the constitutive model of the Arrhenius equation based on Zener-Hollomon parameters was also established in the present investigation. Therefore, optimizing the extrusion temperature to regulate the microstructure, grain orientation distribution, and morphology of precipitates was considered as one of the effective approaches for achieving the excellent mechanical properties of Mg alloys.

Mechanical properties and creep properties of a dilute hot-extruded Mg-Mn-Zn alloy sheet with an ED-tilted texture

Study on the microstructures and tensile creep behaviors of extruded dilute Mg–Mn–Zn alloys

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Mechanical Properties and Deformation Mechanism of Mg-Al-Zn Alloy with Gradient Microstructure in Grain Size and Orientation

Microstructure evolution, mechanical properties and creep mechanisms of Mg-12Gd-1MM-0.6Zr (wt%) magnesium alloy

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

Microstructural Evolution and Mechanical Properties of Mg-5y-5gd-Xnd-0.5zr Magnesium Alloys at Different States

Effects of extrusion process on microstructure, precipitates and mechanical properties of Mg-Gd-Y-Zr-Ag alloys

Compressive creep behavior of extruded Mg-4Sm-2Yb-0.6Zn-0.4Zr alloy

Hot deformation behavior of novel high-strength Mg-0.6Mn-0.5Al-0.5Zn-0.4Ca alloy

Tensile creep behaviors of Mg-10Gd-0.4Zr alloy in different heat treatment states

Effect of transverse gradient extrusion process on texture and mechanical properties of Mg–3Al–1Zn alloy sheets

Anisotropic tensile and degradation properties of as-extruded Mg-6Zn-2Sn-0.5Mn alloy

Microstructure and mechanical properties of Mg-Gd-Zn-Zr alloy after hot extrusion

The microstructure evolution and mechanical anisotropy of extruded Mg-2Zn-0.4Ce-0.4Mn alloy tube during tension in different directions

Opposite effects of Zn addition on the creep resistance at low and high temperatures for as-cast Mg-15Gd alloy

Investigation on corrosion behavior and mechanical properties of an extruded Mg-Zn-Al-Sn-Mn alloy

Hot deformation behavior and extrusion temperature-dependent microstructure, texture and mechanical properties of Mg–1Mn alloy

Microstructure evolution, strengthening mechanisms and deformation behavior of high-ductility Mg−3Zn−1Y−1Mn alloy at different extrusion temperatures

Room-Temperature Strengthening, Portevin-Le Chatelier Effect, High-Temperature Tensile Deformation Behavior, and Constitutive Modeling in a Lightweight Mg-Gd-Al-Zn Alloy

Evading Strength-Ductility Tradeoff in Mg Alloy via Uniform Microstructure and Unique Texture Modification Induced by Moderate Temperature ECAP