Abstract:A novel segmented control strategy for selenization environment is introduced to regulate the selenization reaction by controlling the evaporation area of Se. This selenization method helps to promote element homogenization, optimize surface smoothness, and obtain a high‐crystalline‐quality absorber with low‐point defects. And the CZTSSe solar cell with a PCE of 13.77% is successfully achieved. High‐crystalline‐quality absorbers with fewer defects are crucial for further improvement of open‐circuit voltage (VOC) and efficiency of Cu2ZnSn(S,Se)4 (CZTSSe) solar cells. However, the preparation of high‐quality CZTSSe absorbers remains challenging due to the uncontrollability of the selenization reaction and the complexity of the required selenization environment for film growth. Herein, a novel segmented control strategy for the selenization environment, specifically targeting the evaporation area of Se, to regulate the selenization reactions and improve the absorber quality is proposed. The large evaporation area of Se in the initial stage of the selenization provides a great evaporation and diffusion flux for Se, which facilitates rapid phase transition reactions and enables the attainment of a single‐layer thin film. The reduced evaporation area of Se in the later stage creates a soft‐selenization environment for grain growth, effectively suppressing the loss of Sn and promoting element homogenization. Consequently, the mitigation of Sn‐related deep‐level defects on the surface and in the bulk induced by element imbalance is simultaneously achieved. This leads to a significant improvement in nonradiative recombination suppression and carrier collection enhancement, thereby enhancing the VOC. As a result, the CZTSSe device delivers an impressive efficiency of 13.77% with a low VOC deficit.

Pd(II)/Pd(IV) redox shuttle to suppress vacancy defects at grain boundaries for efficient kesterite solar cells

Defect Regulation by Palladium Incorporation towards Grain Boundaries of Kesterite solar cells

Multinary alloying for facilitated cation exchange and suppressed defect formation in kesterite solar cells with above 14% certified efficiency

A Polymerization‐Assisted Grain Growth Strategy for Efficient and Stable Perovskite Solar Cells

High Efficiency Cu 2 ZnSn(S,Se) 4 Solar Cells with Shallow Li Zn Acceptor Defects Enabled by Solution‐Based Li Post‐Deposition Treatment

Defect Control for 12.5% Efficiency Cu2 ZnSnSe4 Kesterite Thin-Film Solar Cells by Engineering of Local Chemical Environment

High Efficiency Cu2ZnSn(S,Se)4 Solar Cells with Shallow LiZn Acceptor Defects Enabled by Solution‐Based Li Post‐Deposition Treatment

Defect Control for 12.5% Efficiency Cu2ZnSnSe4 Kesterite Thin-Film Solar Cells by Engineering of Local Chemical Environment

Passivating Grain Boundaries via Graphene Additive for Efficient Kesterite Solar Cells

Engineering Solar Cell Absorbers by Exploring the Band Alignment and Defect Disparity: The Case of Cu‐ and Ag‐Based Kesterite Compounds

Synergistic Crystallization Modulation and Defects Passivation in Kesterite via Anion-Coordinate Precursor Engineering for Efficient Solar Cells

Highly efficient, ultrathin, Cd-free kesterite solar cells in superstrate configuration enabled by band level tuning via Ag incorporation

Efficient kesterite Ag-alloyed Cu 2 ZnSn(S,Se) 4 thin film solar cells with a front Ag grading distribution enabled by ZnO insert layer

Segmented Control of Selenization Environment for High‐Quality Cu2ZnSn(S,Se)4 Films Toward Efficient Kesterite Solar Cells

Controlling Selenization Equilibrium Enables High-Quality Kesterite Absorbers for Efficient Solar Cells

Crystallization mechanism and defect passivation of Cu2ZnSn(S,Se)4 thin film solar cells via in situ potassium doping

Optimization of the Selenization Pressure Enabling Efficient Cu 2 ZnSn(S,Se) 4 Solar Cells

Passivation of Deep‐Level Defects through Chemical Environment Regulation for Efficient CZTSSe Solar Cells Based on Active Selenium Adsorption–Desorption Process

SnSe2 Quantum Dots and Chlorhexidine Acetate Suppress Synergistically Non-radiative Recombination Loss for High Efficiency and Stability Perovskite Solar Cells

Controllable Double Gradient Bandgap Strategy Enables High Efficiency Solution‐Processed Kesterite Solar Cells

Grain Boundary Passivation with Dion–Jacobson Phase Perovskites for High‐Performance Pb–Sn Mixed Narrow‐Bandgap Perovskite Solar Cells