Abstract:Multifunctional sensing devices with high flexibility, high sensitivity, and scalable fabrication are inevitable components of Internet of Things (IoT) for human–machine interfaces, structural health monitoring, and soft robots. Herein, high-performance flexible sensor arrays using carboxymethylcellulose (CMC) and its composite were developed for mechanical and thermal stimuli detection by laser direct writing. CMC contains abundant carbon precursors for strain-sensitive laser-carbonized CMC (LC-CMC), while the incorporation of graphene oxide (GO) into CMC leads to the formation of thermal-sensitive laser-carbonized GO/CMC (LC-GO/CMC). The LC-CMC-based strain sensor delivers gauge factors of 487.7 (strain < 8.5%) and 8557 (8.5% < strain < 14%), with long-term stability over 10 000 cycles. With 0.2 wt % GO, the LC-GO/CMC-based device provides a temperature coefficient of resistance of −0.289% °C <sup>–1</sup>, higher than the Cr-based commercial sensor. The potential application of the devices in IoT is proved by combining the near-field communication technology with the LC-CMC-based device to monitor the strain suffered by 316L stainless steel during the fatigue test. Moreover, an integrated device based on the strain and temperature sensing arrays accomplishes the simultaneous measurement of temperature and mechanical deformation in real time.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c21168?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c21168</a>.Photography of LC-CMC-based patterns; optical images of LC-CMC-based samples; calculation results of the heat transition process at the interface of the laser beam and CMC substrate; SEM, TEM, and XPS analyses of LC-CMC- and LC-GO/CMC-based samples; electrical response of the LC-GO/CMC-based temperature sensor under different concentrations of GO solution; application of the devices combining NFC technology with LC-CMC-based strain sensors to monitor the strain suffer by 316L materials during stretch–release cycles; table of conductivity and statistic data for widths of carbonization area of LC-CMC-based samples generated under different laser powers and writing speeds (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c21168/suppl_file/am0c21168_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Alumina ceramic insulation layer for strain sensor fabricated by direct laser deposition

Electrical insulation improvement using a CeYSZ/Al2O3 double ceramic layer underlayer for thin-film sensors

Preparation of defect-free alumina insulation film using layer-by-layer electrohydrodynamic jet deposition for high temperature applications

Novel Surface Acoustic Wave Strain Sensor with Enhanced High-Temperature Performance and Resistance to Aging

Study on Laser-Stricken Damage to Alumina Ceramic Layer of Different Surface Roughness

Laser direct writing of a multifunctional superhydrophobic composite strain sensor with excellent corrosion resistance and Anti-Icing/Deicing performance

Melt-grown behaviour of heat treated high-purity alumina ceramics prepared by laser directed energy deposition

Development of highly sensitive and stable patterned PDMS flexible strain sensors for motion monitoring via laser direct writing

Laser Direct-Write Sensors On CFR-PEEK For Smart Orthopedic Implants

In-Situ Reaction Deposition Of Alumina Ceramic Film By Laser-Induced Vacuum Arc

High Performance NbMoTa–Al2O3 Multilayer Composite Structure Manufacturing by Laser Directed Energy Deposition

Highly stretchable, superhydrophobic and wearable strain sensors based on the laser-irradiated PDMS/CNT composite

High-precision resistance strain sensors of multilayer composite structure via direct ink writing: Optimized layer flatness and interfacial strength

Investigation of temperature field for the in-situ fabrication of particle-reinforced alumina ceramics coating via laser induction

Predicting rapid growth behavior in solidified eutectic ceramic composites using infrared thermal imaging and thermal field simulation during laser directed energy deposition

A high-performance, sensitive, low-cost LIG/PDMS strain sensor for impact damage monitoring and localization in composite structures

Microstructures and mechanical properties of additively manufactured alumina ceramics with digital light processing

Formation mechanism and controlling strategy of lamellar structure in 3D printed alumina ceramics by digital light processing

Insights into the influence of powder particle shape on forming process and mechanical properties of Al2O3 ceramic fabricated by laser directed energy deposition

Digital light processing‐based additive manufacturing of orientation‐controlled Al2O3 ceramics with improved damage tolerance

Laser Direct Writing of Flexible Sensor Arrays Based on Carbonized Carboxymethylcellulose and Its Composites for Simultaneous Mechanical and Thermal Stimuli Detection