Abstract:This study investigated defect formation and strain distribution in high-Mg-content Al-Mg alloys during normal rolling and cross-rolling processes. The finite element analysis (FEA) revealed the presence of wave defects and strain localization-induced zipper cracks in normal cold rolling, which were confirmed by the experimental results. The concentration of shear strain played a significant role in crack formation and propagation. However, the influence of wave defects was minimal in the cross-rolling process, which exhibited a relatively uniform strain distribution. Nonetheless, strain concentration at the edge and center regions led to the formation of zipper cracks and edge cracks, with more pronounced propagation observed in the experiments compared to FEA predictions. Furthermore, texture evolution was found to be a crucial factor affecting crack propagation, particularly with the development of the Goss texture component, which was observed via electron backscattered diffraction analysis at bending points. The Goss texture hindered crack propagation, while the Brass texture allowed cracks to pass through. This phenomenon was consistent with both FEA and experimental observations. To mitigate edge crack formation and propagation, potential strategies involve promoting the formation of the Goss texture at the edge through alloy and process conditions, as well as implementing intermediate annealing to alleviate stress accumulation. These measures can enhance the overall quality and reliability of Al-Mg alloys during cross-rolling processes. In summary, understanding the mechanisms of defect formation and strain distribution in Al-Mg alloys during rolling processes is crucial for optimizing their mechanical properties. The findings of this study provide insights into the challenges associated with wave defects, strain localization, and crack propagation. Future research and optimization efforts should focus on implementing strategies to minimize defects and improve the overall quality of Al-Mg alloys in industrial applications.

Investigation into the anisotropic damage behavior of LA103Z Mg‐Li alloy rolling sheet using X‐ray computed tomography and numerical modeling

Influences of stress states and loading directions on the anisotropic fracture of magnesium alloy AZ31B sheet under tension-dominated forming conditions

Damage Analysis of Hot-Rolled AZ31 Mg Alloy Sheet During Uniaxial Tensile Testing under Different Loading Directions

A continuum damage model for Mg/Al composite sheets rolling: Theoretical development and application

Quantitative analysis of the deformation modes and cracking modes during low-cycle fatigue of a rolled AZ31B magnesium alloy: The influence of texture

Study on Rolling Defects of Al-Mg Alloys with High Mg Content in Normal Rolling and Cross-Rolling Processes

Modeling and Evaluation of Damages in Bismuth-containing Stainless Steel Rolling

Effect of Rolling Strain on Microstructure and Tensile Properties of Dual-Phase Mg–8Li–3Al–2Zn–0.5Y Alloy

Forming Limit Analysis of Mg-2Zn-1.2Al-0.2Ca-0.2RE Alloy Sheet Using Ductile Fracture Models

Microstructure, texture evolution and mechanical anisotropy of Mg-Gd-Y-Zn-Zr alloy sheets produced by unidirectional and cross rolling

Anisotropic Ductile Fracture: Experiments, Modeling, and Numerical Simulations

Grain size and orientation affected deformation inhomogeneity and local damage of hot-deformed Al-Zn-Mg alloy

Study on Mechanical Behaviors and Theoretical Critical Shear Strength of Cold-Rolled AZ31 Alloy with Different Li Additions

Anisotropic Gurson-Tvergaard-Needleman model considering the anisotropic void behaviors

Deformation mechanism, orientation evolution and mechanical properties of annealed cross-rolled Mg-Zn-Zr-Y-Gd sheet during tension

Prediction of edge cracks and plastic-damage analysis of Mg alloy sheet in rolling

Anisotropic mechanical behavior prediction of aluminum alloy sheet based on an anisotropic GTN model: Modeling, simulation and experimental investigation

Study on Forming Defects in the Rolling Process of Large Aluminum Alloy Ring Via Adaptive Controlled Simulation

Microstructure and Mechanical Properties of Mg-Gd-Y-Zn-Mn Alloy Sheets Processed by Large-Strain High-Efficiency Rolling

Effect of Quasicrystal I-Phase on Microstructure and Mechanical Properties of Hot-Rolled Diphasic Mg-8 Wt.% Li Alloy

Ductile fracture behavior in micro-scaled progressive forming of magnesium-lithium alloy sheet