Abstract:Carbon-based inorganic CsPbX3 (X = I, Br, Cl) perovskite solar cells (PSCs) are attracting great attention in the photovoltaic field because of their low cost, simple process, and superior thermal stability. However, the large difference in energy band between the CsPbX3 and carbon electrode leads to the poor hole extraction and unfavorable charge recombination, thus deteriorating device's efficiency. In this work, a solution-processed dopant-free tin phthalocyanine (SnPc) film is used as a hole-transport layer (HTL) to fabricate carbon-based CsPbI2Br PSCs by a low-temperature process. At the optimal process, the device achieves a maximum efficiency of 11.39% with less hysteresis, which is much higher than 9.22% of reference device without the SnPc HTL. Moreover, the unencapsulated device exhibits the improved stability and remains about 90% of its initial efficiency after 30 days in ambient air (20–25 °C) with 25–35% relative humidity (RH). This finding reveals that the solution-processed dopant-free SnPc HTL can significantly promote charge transport and suppress charge recombination at the CsPbI2Br/carbon interface. This work provides a low-temperature and solution-processed method to fabricate the efficient and stable carbon-based inorganic PSCs.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsaem.0c01184?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsaem.0c01184</a>.Photovoltaic parameters corresponding to Table S1, Table S4, Figure S3, and Figure S9; quantified atomic ratio for the SnPc-film as obtained from EDS measurement; a summary of annealing temperature, Voc, and PCE values measured under RS direction for carbon-based CsPbI2Br PSCs reported in recent years; the values of Jph*, Jph#, Jsat, Jph*/Jsat, Jph#/Jsat, and Gmax; fitting parameters of TRPL decay spectra; fitting values of different electronic parameters obtained from the Nyquist plots; XRD patterns and photo images of PbI2, PbI2(DMSO), PbBr2, and PbBr2(DMSO) powders; thickness of SnPc HTL measured by an ellipsometer; J–V curves of SnPc-PSCs with different SnPc solution concentrations; EDS spectra of the SnPc-film; XRD patterns of SnPc powder and SnPc film annealed at 120 °C; the schematic of energy level diagram; the steady-state current density as a function of time measured at the maximum power output point; spectrum for the thickness of CsPbI2Br layer; two possible growth models while depositing solution-processed dopant-free SnPc on the CsPbI2Br surface; KPFM images and CPD values of SnPc films based on different SnPc solution concentrations (<a class="ext-link" href="/doi/suppl/10.1021/acsaem.0c01184/suppl_file/ae0c01184_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

A Buried Functional Layer for Inorganic CsPb 0.75 Sn 0.25 I 2 Br Perovskite Solar Cells

A Buried Functional Layer for Inorganic CsPb0.75Sn0.25I2Br Perovskite Solar Cells

Cspb0.9sn0.1ibr2 Based All-Inorganic Perovskite Solar Cells With Exceptional Efficiency And Stability

Regulating the Interplay at the Buried Interface for Efficient and Stable Carbon-Based CsPbI2Br Perovskite Solar Cells

CsPb0.9Sn0.1IBr2 Based All-Inorganic Perovskite Solar Cells with Exceptional Efficiency and Stability.

A Solution-Processed Dopant-Free Tin Phthalocyanine (snpc) Hole Transport Layer for Efficient and Stable Carbon-Based CsPbI2Br Planar Perovskite Solar Cells Prepared by a Low-Temperature Process

Oxalate Pushes Efficiency of CsPb 0.7 Sn 0.3 IBr 2 Based All‐Inorganic Perovskite Solar Cells to over 14%

An intermeshing electron transporting layer for efficient and stable CsPbI2Br perovskite solar cells with open circuit voltage over 1.3 V

High‐Efficiency and Stable Perovskite Solar Cells via Buried Interface Modification with Multi‐Functional Phosphorylcholine Chloride

A Solution-Processed Dopant-Free Tin Phthalocyanine (SnPc) Hole Transport Layer for Efficient and Stable Carbon-Based CsPbI 2 Br Planar Perovskite Solar Cells Prepared by a Low-Temperature Process

Efficient and Stable Perovskite Solar Cells by B-Site Compositional Engineered All-Inorganic Perovskites and Interface Passivation

Strengthened Buried Interface via Metal Sulfide Passivation towards High‐Performance CsPbBr3 Perovskite Solar Cells

CsPbI3 Based All‐Inorganic Perovskite Solar Cells: Further Performance Enhancement of the Electron Transport Layer‐Free Structure from Device Simulation

Bridging the buried interface with conjugated molecule for highly efficient carbon-based inorganic CsPbI 2 Br perovskite solar cells fabricated in air

Bridging the Buried Interface with Conjugated Molecule for Highly Efficient Carbon-Based Inorganic CsPbI2Br Perovskite Solar Cells Fabricated in Air

Improvement of Thermal Stability and Photoelectric Performance of Cs2PbI2Cl2/CsPbI2.5Br0.5 Perovskite Solar Cells by Triple-Layer Inorganic Hole Transport Materials

Interface Engineering for All‐Inorganic CsPbIBr 2 Perovskite Solar Cells with Enhanced Power Conversion Efficiency over 11%

Multistrategy Toward Highly Efficient and Stable CsPbI 2 Br Perovskite Solar Cells Based on Dopant‐Free Poly(3‐Hexylthiophene)

Achieving 17.46% Efficiency CsPbI2Br Perovskite Solar Cells via Multifunction Lead Chloride‐Modified ZnO Electron Transporting Layer

Chlorobenzenesulfonic Potassium Salts as the Efficient Multifunctional Passivator for the Buried Interface in Regular Perovskite Solar Cells

Effective defect passivation with a designer ionic molecule for high-efficiency vapour-deposited inorganic phase-pure CsPbBr3 perovskite solar cells