Abstract:Wire-arc directed energy deposition (DED) has attracted significant interest for the fabrication of large-sized, lightweight Mg-alloy components. However, these components generally exhibit poor mechanical properties and limited corrosion resistance owing to their inherent residual stress and non-equilibrium microstructures. Herein, laser shock peening (LSP) was adopted to successfully modify the stress state and microstructure of AZ31 Mg-alloy fabricated using wire-arc DED. The influence of LSP on the residual stress, mechanical properties, electrochemical behaviour, and microstructural evolution was systematically investigated. The experimental results indicate that, compared with the as-built specimen, the performance of the LSP-treated specimen was notable, with a ≈63.8% decrease in the corrosion current density and ≈30% and ≈13% decreases in the yield strength (YS) and ultimate tensile strength, respectively. The enhanced corrosion resistance can be attributed to the LSP-induced compressive residual stress, nanograins, and nanoparticles. Nanocrystallisation, particle refinement, dense mechanical twins (MTs), and planar dislocation arrays (PDAs) jointly contributed to the enhancement of the YS. The LSP-induced nanocrystallisation was rationalized by the accumulation of PDAs, the intersection of multiple nano-MTs, and the transformation of nano-MTs blocks into sub-grains and then into nanograins owing to continuous dynamic recrystallisation. The particle refinement mechanism involved dislocation proliferation and the development of dislocation slip bands, which eventually led to fragmentation and separation. Therefore, this study introduces a LSP post-treatment technology for the residual stress regulation, microstructural modification, and performance enhancement of Mg alloys fabricated using wire-arc DED. Based on the ability of LSP to tailor the microstructure and performance of Mg alloys, a novel method of wire-arc DED with online LSP treatment is proposed. This method can achieve in-situ surface strengthening and the integrated formation of large-sized components with complex geometries.

Investigation of bypass-coupled double-pulsed directed energy deposition of Al–Mg alloys

Enhanced High-Temperature Strength and Ductility of Wire Arc Additive Manufactured Al-Ce-Mg Alloys with Fine Α-Al/al11ce3 Eutectics

Tailoring properties of directed energy deposited Al-Mg alloy by balancing laser shock peening and heat treatment

Double pulsed current adopted in local dry underwater WAAM to simultaneously enhanced strength and ductility of 308 L multi-layer component

Wire-arc directed energy deposited Mg-Al alloy assisted by ultrasonic vibration: Improving properties via controlling grain structures

Wire arc additive manufacturing of Al-Zn-Mg-Cu alloy: Microstructures and mechanical properties

A comparative study on microstructure and mechanical properties of wire-arc directed energy deposited Al–Zn–Mg–Cu alloy based on the cold metal transfer technology

Microstructures and Properties of Al-Mg Alloys Manufactured by WAAM-CMT

Investigate the effect of arc characteristic on the mechanical properties of 5A56 Al alloy in CMT arc additive manufacturing

Enhancing the geometry accuracy and mechanical properties of wire arc additive manufacturing of an Al-5%Mg alloy through longitudinal magnetic field influence

Comparative investigation of wire arc additive manufacturing of Al-5%Mg alloy with and without external alternating magnetic field

Regional Control and Optimization of Heat Input during CMT by Wire Arc Additive Manufacturing: Modeling and Microstructure Effects

Minimizing porosity and optimizing microstructure of hot-wire arc additive manufactured Al-Cu-Mg-Ag alloy for strength increment

Gradient microstructure and prominent performance of wire-arc directed energy deposited magnesium alloy via laser shock peening

Research on high efficiency deposition method of titanium alloy based on double-hot-wire arc additive manufacturing and heat treatment

Wire arc metal additive manufacturing using pulsed arc plasma (PAP-WAAM) for effective heat management

Enhancing strength, ductility, and fatigue performance of Al-Zn-Mg-Cu-Sc-Zr alloy using a hybrid approach: Wire-arc directed energy deposition and interlayer friction stir processing

Process Optimization, Microstructure and Mechanical Properties of Wire Arc Additive Manufacturing of Aluminum Alloy by Using DP-GMAW Based on Response Surface Method

Investigation on High-deposition-rate Directed Energy Deposition of Al-5%Mg Alloy Via External Compound Magnetic Fields

Wire Arc Additive Manufacturing (WAAM) of Aluminum Alloy AlMg5Mn with Energy-Reduced Gas Metal Arc Welding (GMAW)

Elucidating the effects of metal transfer modes and investigating the material properties in wire-arc additive manufacturing (WAAM)