Abstract:In order to optimize the fabrication quality, an external longitudinal alternating magnetic field is introduced into the wire arc additive manufacturing (WAAM) system of aluminum alloy in this investigation. The arc behavior, metal transfer, deposit morphology, microstructure, and mechanical properties of WAAM of Al-5%Mg alloy with and without external magnetic field (EMF) are investigated comprehensively and comparatively. Results indicate that the increase of excitation current promotes the dilatation of arc plasma to reduce the heat flux density, broadens the bead width, and decreases the bead height and penetration depth, while the increase of excitation frequency has the opposite effect on those. Furtherly, the spray transfer process which occurs at the beginning of each welding wire motion cycle can be restricted under appropriate excitation current and excitation frequency. Compared with that without EMF, the surface accuracy of thin-wall parts deposited with the EMF of excitation current 2 A and excitation frequency 70 Hz is remarkably improved, whose surface waviness is decreased by 34%. Simultaneously, the secondary phase of Al3Mg2\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$${Al}_{3}{Mg}_{2}$$\end{document} is distributed more uniformly, and the number and dimension of pores of deposit are greatly reduced. The microstructures in the bottom layer and top layer of deposit with EMF get furtherly refined by the electromagnetic stirring, but those in the middle layers and final tensile properties of the deposit are not obviously optimized, which are mainly caused by severe heat accumulation and repeated heating from subsequent deposition, and the nature of non-heat treatment strengthening of Al–Mg alloy.

Enhancing the geometry accuracy and mechanical properties of wire arc additive manufacturing of an Al-5%Mg alloy through longitudinal magnetic field influence

Enhanced High-Temperature Strength and Ductility of Wire Arc Additive Manufactured Al-Ce-Mg Alloys with Fine Α-Al/al11ce3 Eutectics

Improving mechanical strength and isotropy for wire-arc additive manufactured 304L stainless steels via controlling arc heat input

Impact of Process Parameters on Forming Quality and Deposition Efficiency of Unsupported Rods in Wire Arc Additive Manufacturing

Preparation and characterization of CMT wire arc additive manufacturing Al-5%Mg alloy depositions through assisted longitudinal magnetic field

Enhancing wire arc additive manufacturing in vibrational environments with longitudinal magnetic fields

Comparative investigation of wire arc additive manufacturing of Al-5%Mg alloy with and without external alternating magnetic field

Minimizing porosity and optimizing microstructure of hot-wire arc additive manufactured Al-Cu-Mg-Ag alloy for strength increment

Variations of the improved characteristics on microstructure and mechanical properties of Al–Cu alloy fabricated by magnetic field assisted wire-arc additive manufacturing after heat-treated

Wire arc additive manufacturing of Al-Zn-Mg-Cu alloy: Microstructures and mechanical properties

Effect of auxiliary longitudinal magnetic field on overlapping deposition of wire arc additive manufacturing

Improving mechanical properties of wire arc additively manufactured AA2196 Al–Li alloy by controlling solidification defects

Microstructure and Mechanical Properties of AlSi7Mg0.6 Aluminum Alloy Fabricated by Wire and Arc Additive Manufacturing Based on Cold Metal Transfer (WAAM-CMT)

Achieving high strength-ductility of Al-Zn-Mg-Cu alloys via hot-wire arc additive manufacturing enabled by strengthening precipitates

Microstructure evolution and mechanical properties of the wire + arc additive manufacturing Al-Cu alloy

Wire arc additive manufacturing of a novel ATZM31 Mg alloy: Microstructure evolution and mechanical properties

Microstructures and Properties of Al-Mg Alloys Manufactured by WAAM-CMT

Improvement of microstructure and fatigue performance of wire-arc additive manufactured 4043 aluminum alloy assisted by interlayer friction stir processing

Mechanical properties and microstructure characteristics of wire arc additively manufactured high-strength steels

Multiscale modelling of microstructure, micro-segregation, and local mechanical properties of Al-Cu alloys in wire and arc additive manufacturing

Laser cleaning assisted wire arc additive manufacturing of aluminum alloy thin-wall through synchronous wire-powder deposition