Abstract:Here, through the effective passivation of thick film defects in perovskite by employing the RbX addition strategy, the crystalline quality, enhances the device performance of bifacial perovskite solar cells (PSCs), positioning them at the forefront of current research in this field. The front photovoltaic conversion efficiency reaches 21.04%, with a bifaciality of ≈80%, achieving an power generation density (PGD) of 24.36 mW cm−2 at a albedo of 0.2. Bifacial perovskite solar cells (PSCs) possess a dual light‐absorbing structure, which enables higher power output at lower additional costs. However, the replacement of metal electrodes with transparent ones leads to serious light loss, necessitating a thicker perovskite layer to compensate for this drawback. In this study, the impact of different rubidium halide (RbCl, RbBr, and RbI) additives is systematically investigated on precursor solubility and the quality of micron‐sized perovskite thick films prepared using a two‐step method. It is observed that RbCl exhibited the strongest interactions with PbI2, enhancing its solubility and leading to the formation of multihole PbI2 films that promote subsequent crystallization of thick perovskite film. Additionally, the RbCl‐based perovskite film demonstrates a narrowed bandgap attributed to the formation of a‐FAPbI3. Consequently, the short‐circuit current density (Jsc) and open‐circuit voltage (Voc) in the RbCl‐based bifacial PSCs are simultaneously enhanced, and a record efficiency of 20.86% (21.04% certified) is also obtained among n‐i‐p bifacial PSCs, exhibiting an ≈80% bifaciality and a power generation density (PGD) exceeding 24 mW cm−2 with a reflectivity value of 0.2. More importantly, the optimized device does not show any performance degradation after continuous illumination under 1sun for 1000 h.

Simultaneous Interfacial Defect Passivation and Bottom-Up Excess PbI 2 Management via Rubidium Chloride in Highly Efficient Perovskite Solar Cells with Suppressed Hysteresis

High Performance Inverted RbCsFAPbI3 Perovskite Solar Cells Based on Interface Engineering and Defects Passivation.

Simultaneous Defect Passivation and Electric Level Regulation with Rubidium Fluoride for High-Efficiency CsPbI 2 Br Perovskite Solar Cells

Synergetic Excess PbI2 and Reduced Pb Leakage Management Strategy for 24.28% Efficient, Stable and Eco‐Friendly Perovskite Solar Cells

Excess PbI2 Management via Multimode Supramolecular Complex Engineering Enables High‐Performance Perovskite Solar Cells

Suppressing the crystallographic disorders induced by excess PbI 2 to achieve trade-off between efficiency and stability for PbI 2 -rich perovskite solar cells

Unraveling the Passivation Process of PbI2 to Enhance the Efficiency of Planar Perovskite Solar Cells

Synchronous Elimination of Excess Photoinstable PbI2 and Interfacial Band Mismatch for Efficient and Stable Perovskite Solar Cells

Ligand‐Modulated Excess PbI2 Nanosheets for Highly Efficient and Stable Perovskite Solar Cells

Managing Multiple Halide-Related Defects for Efficient and Stable Inorganic Perovskite Solar Cells

Defects in CsPbX3 Perovskite: From Understanding to Effective Manipulation for High-Performance Solar Cells

Lead (Pb) Management in the Entire Life Cycle of Highly Efficient and Stable Perovskite Solar Cells

Synchronous Surface Reconstruction and Defect Passivation for High-Performance Inorganic Perovskite Solar Cells.

Simultaneous dual-interface and bulk defect passivation for high-efficiency and stable CsPbI2Br perovskite solar cells

Tri‐Brominated Perovskite Film Management and Multiple‐Ionic Defect Passivation for Highly Efficient and Stable Solar Cells

Modulating Residual Lead Iodide via Functionalized Buried Interface for Efficient and Stable Perovskite Solar Cells

Hierarchically Manipulated Charge Recombination for Mitigating Energy Loss in CsPbI 2 Br Solar Cells

Efficient Liquid‐Solid Coregulation Engineering in Mixed‐cation Lead Mixed‐halide Perovskite for Photovoltaic Performance Improvement

Managing Interface Defects via Mixed‐Salt Passivation toward Efficient and Stable Perovskite Solar Cells

Rubidium Halide Additive Engineering for Efficient and Stable Bifacial Perovskite Solar Cells

Multifunctional Small Molecule as Buried Interface Passivator for Efficient Planar Perovskite Solar Cells