Abstract:Combustion of agricultural residues for heat and electricity production is an efficient way to reduce amount of such waste source and emissions due to inappropriate treatment of them. However, unlike other biomass materials, agricultural residues often have high content of ash and certain ash forming elements with low meting temperatures, resulting in sintering and slagging during combustion processes. It complicates combustion of agricultural residues and restricts further utilization of this renewable energy source. In this work, sintering of a typical agricultural biomass cornstalk and effect of two phosphate additives, Ca(H2PO4)2·H2O and NH4H2PO4, were investigated by a combination of various techniques. Results indicated that the addition of Ca(H2PO4)2·H2O increased the initial melting temperature of cornstalk ash by 64–209 °C. The ash sintering behavior was greatly improved as a result of formation of high melting temperature K–Ca phosphates, Ca9MgK(PO4)7 and Ca2KP3O10 upon addition of the Ca(H2PO4)2·H2O. It is accompanied with reduced generation of low melting temperature K-rich silicates and the formation of large ash aggregates. Addition of NH4H2PO4 increased the initial ash melting temperature by 28–116 °C, but it had slight influence on the cornstalk ash sintering characteristics. The analysis revealed that, although the addition of NH4H2PO4 resulted in the formation of high melting temperature K2CaP2O7, certain amount of K phosphates and silicates eutectics were still formed, initiating and promoting sintering of ash from mixture of cornstalk and NH4H2PO4. Reactions between Ca(H2PO4)2·H2O and potassium salts under different conditions were also studied. It was found that reactions between Ca(H2PO4)2·H2O and potassium salts might already start as the temperature higher than 300 °C. K2CaP2O7, Ca2P2O7, Ca(PO3)2 and KCa(PO3)3 were identified as main products from these reactions and amounts of them considerably depends on the heat treatment temperatures and mixing ratios between Ca(H2PO4)2·H2O and potassium salts. Compared to KCl, K2CO3 had a higher reactivity toward the Ca(H2PO4)2·H2O under same study conditions. The current work shows the addition of Ca(H2PO4)2·H2O is a promising approach to alleviate the ash sintering issues and assure efficient and smooth combustion of cornstalk.

What problem does this paper attempt to address?

The paper attempts to address the issue of slagging and melting during the combustion of corn straw, which is caused by the formation of low-melting-point substances in the ash. Specifically, corn straw, as an agricultural waste, produces ash containing a large amount of potassium, chlorine, and silicon when burned. These elements easily form low-melting-point compounds at high temperatures, leading to slagging and melting inside the combustion equipment, severely affecting combustion efficiency and the normal operation of the equipment. To solve this problem, researchers explored the impact of adding phosphorus-based additives (such as Ca(H₂PO₄)₂·H₂O and NH₄H₂PO₄) on the melting characteristics and slagging behavior of corn straw ash. Through experimental research, the paper evaluates the effects of different phosphorus-based additives on the melting temperature and slagging characteristics of corn straw ash. It also analyzes the mechanism by which the additives react with potassium salts in the ash to form high-melting-point phosphates, aiming to provide theoretical guidance and technical support for alleviating ash melting and slagging issues in the combustion process of agricultural biomass.

Effect of phosphorus-based additives on the sintering characteristics of cornstalk ash

Effect of Ash Preparation Method on the Sintering Characteristics of Ashes from Combustion of Coal and Biomass Blends

Mechanism of Na2O/CaO Ratio Affecting Ash Fusing Characteristics During Ash Deposition and Slagging in Municipal Solid Waste Incinerator

Effect of additives on fusion characteristic of ashes during rice straw combustion

Effects of additives blended in corn straw to control agglomeration and slagging in combustion

Effect of phosphorus-based additives on ash fusion characteristics of high-sodium coal under gasification condition

Impact of ammonium sulfate and kaolin on ash deposition during co-firing of straw pellets and pulverized coal

The impact of aluminosilicate-based additives upon the sintering and melting behaviour of biomass ash

Ash Melting Behavior of Rice Straw and Calcium Additives

Investigation on Ash Slagging Characteristics During Combustion of Biomass Pellets and Effect of Additives

Ash melting and slagging and residual K ion content in biomass pellet combustion

Effect of Coal Ash on the Reduction and Roasting Processes of Phosphogypsum

Effects of phosphorous-based additive on flow properties of high silicon-aluminum coal ash

Experimental Study on the Effects of Calcium-Based Additives to Control Ammonium Bisulfate and Ash Mixture Deposition with an On-Line Digital Image Technique

Enhancement of the Plant‐Accessible Phosphate Fraction in Sewage Sludge Ashes by Na+ or K+ Addition Prior to Combustion

Effects of P-based additives on agricultural biomass torrefaction and particulate matter emissions from fuel combustion

Combined effect of ball-milled ash and ammonium dihydrogen phosphate on fouling, slagging, and combustion characteristics of high-sodium zhundong coal

Understanding effect of phosphorus-based additive on ash deposition characteristics during high-sodium and high-calcium Zhundong coal combustion in drop-tube furnace

A comparison study of the inhabitation effect of phosphate tailing and kaolin on the release of K in biomass straw

Investigation of Biomass Ash Sintering Characteristics and the Effect of Additives

Influence of Coal Ash on the Characteristics of Corn Straw Pyrolysis Products.