Abstract:The flow temperature (FT) of the coal ash from the Liuqiao no. 2 mine in North Anhui Province (C00) is too high (∼1520 °C) to fit the Shell gasifier due to its relatively high content of SiO2 and Al2O3. To solve this problem, a series of coals were blended with C00 with different ratios, and the relations between FT and the ash composition were investigated. The coal ash was analyzed by X-ray diffraction, Fourier transform infrared (FTIR) spectroscopy, and scanning electron microscopy–EDX to elucidate the mechanism of the improved ash fusion performance and the slag formation in the waste heat boiler of the gasifier. It is shown that FT is relevant to the coal ash compositions as well as the structures formed at high temperatures. The existence of alkaline oxides (CaO, MgO, and Fe2O3) decreases the coal ash FT to a low level. The FT can decrease to <1350 °C to cater to the Shell gasifier by blending C00 and C03 with a mass ratio of 4:6 owing to the plentiful alkaline oxides in C03. The FTIR results indicate that the high flow temperature of C00 is attributed to the formation of mullite at high temperatures. The coal blending with various ratios changes the compositions of CaO, MgO, and Fe2O3, which can form some low-melting-point eutectic compounds with SiO2 and Al2O3 under high temperatures, inhibit the formation of mullite, and thus decrease the ash FT. The coal ash FT was found to have a good linear relation with the ash compositions, which can sever as a reference to the coal blending. According to the model parameters, it is shown that Mg has the most significant promoting effect on the decrease in FT of the coal ash. The caking tendency of fly ash increases with the rising Ca content and an excessive Ca-based fluxing agent used in the coal blending will lead to the aggregation of the Ca-rich clasts around the fly ash particle, resulting in the plugging of the waste heat boiler in the gasifier. Therefore, the Mg-based fluxing agent is more promising to improve the ash fusion performance and reduce the caking tendency of the coal fly ash.This article has not yet been cited by other publications.

Effects of phosphorous-based additive on flow properties of high silicon-aluminum coal ash

Effect of Coal Ash on the Reduction and Roasting Processes of Phosphogypsum

Mechanism of Na2O/CaO Ratio Affecting Ash Fusing Characteristics During Ash Deposition and Slagging in Municipal Solid Waste Incinerator

Effect of phosphorus-based additives on ash fusion characteristics of high-sodium coal under gasification condition

Effect of phosphorus-based additives on sodium release during Zhundong coal gasification in flat flame-assisted entrained flow reactor

Effecting mechanisms of iron-rich sludge on ash fusion characteristics of coal with high ash fusion temperature under reducing atmosphere

Correlation between Flow Temperature and Average Molar Ionic Potential of Ash during Gasification of Coal and Phosphorus-Rich Biomass

Understanding effect of phosphorus-based additive on ash deposition characteristics during high-sodium and high-calcium Zhundong coal combustion in drop-tube furnace

Effects of phosphorus on the fusion characteristics of synthetic ashes with different Al 2 O 3 /CaO ratios

Effect of Chemical Compositions on Ash Fusibility Characterization of a Jincheng Anthracite During Combustion and Gasification

Influence of phosphorus on ash fouling deposition of hydrothermal carbonization sewage sludge fuel via drop tube furnace combustion experiments

Ash fusion behaviors of sugarcane bagasse and its modification with sewage sludge addition

Investigation on Release and Migration Characteristics of Sodium During the Combustion of High-Sodium Coal with Phosphorite

Quantitative analysis of minerals of blended coal ash at high temperature and its influence on slagging

Understanding Ash Sintering Variation Behaviors of Low-Rank Coals with Municipal Sludge Addition Based on Mineral Interactions

Melting Characteristics of Coal Ash and Properties of Fly Ash to Understand the Slag Formation in the Shell Gasifier

Effect of Phosphorus Transformation on the Reduction of Particulate Matter Formation During Co-combustion of Coal and Sewage Sludge

High-Temperature Ash Melting and Fluidity Behavior upon the Cocombustion of Sewage Sludge and Coal

Effect of Ca3(PO4)2 additive on the slagging behavior during the cofiring of high‐sodium coal and iron-rich coal

Effect of additives on flow characteristics and sodium capture efficiency of high alkali coal ash slag

Slagging inhibition through co-firing of coal gangue and high sodium coal: An experimental and modelling study