Abstract:Although there are various methods to measure the modulation transfer function (MTF) of charge-coupled devices (CCD). the interferometric fringe pattern method has advantages over others, such as canted slit sources, bar targets, knife-edge, laser-speckle patterns, random noise pattern, etc. Our interferometric method is relatively simple and versatile: It requires no critical optics and no focusing or precision alignment, the entry array is tested, the contrast ratio of the test pattern is high enough, the spatial frequency of the fringe pattern can vary continuously. Our method generates the formation of a sinusoidal intensity fringe pattern by the interference of two monochromatic plane waves, and straightforward projects it onto the CCD array under test. The construction of the experimental device is based on the Fresnel Double-Mirror structure. A 2.5 mw He-Ne laser with the wavelength of 632.8 nm is used as the light source, the laser beam is spatially filtered by a 10 mu m pinhole and expanded to a diameter of 30 mm, and the resulting wave front is divided by two mirrors, which incline to each other at a small angle, and interfered. One of the mirrors is rotatable to vary the frequency of the pattern. The CCD array is mounted on a stage, which is also rotatable to make that the CCD array takes different angle with the fringe pattern direction, to receive the patterns. With the method we provided, the spatial frequency can be extended to some 2 times the Nyquist frequency of the CCD array to study the aliasing effect. In the Cartesian coordinates, the x- and y- axis MTFs (at angle 0 degrees and 90 degrees) of the CCD array were measured, the other three MTFs (at angle 26.56 degrees, 45 degrees and 63.44 degrees), which nobody has done before, were also tested offering a more comprehensive characterization of the CCD array.

Calibration-free scheme for frequency response measurement of a Mach–Zehnder modulator with low-frequency detection

Modulation transfer function measurement of charge-coupled devices using frequency-variable fringe patterns

High Accuracy Microwave Frequency Measurement Based on Single-Drive Dual-Parallel Mach-Zehnder Modulator

Thin‐Film‐Lithium‐Niobate Photonic Chip for Ultra‐Wideband and High‐Precision Microwave Frequency Measurement

A Fast Vibration-Level Adjustment Method for Low-Frequency Vibration Calibration Based on Modified Filtered-X Least Mean Square Algorithm

Practical system for phase noise measurement of optoelectronic oscillators

A Bridged Contactless Measurement Technique for LC Tank Based Voltage-Controlled Oscillator.

A Frequency-Domain I/Q Imbalance Calibration Algorithm for Wideband Direct Conversion Receivers Using Low-Cost Compensator.

A New Capacitance-to-Frequency Converter for On-Chip Capacitance Measurement and Calibration in CMOS Technology

Accurate Calibration and Measurement of Optoelectronic Devices

Measuring the Frequency Response of Photodiode Using Phase-Modulated Interferometric Detection

Instantaneous Microwave Frequency Measurement Using an Optical Phase Modulator

Ultra-wide frequency response measurement of an optical system with a DC photo-detector

A microwave photonic scheme for improving the sensitivity of Mach-Zehnder optical fiber interferometer sensor

Note: an in Situ Method for Measuring the Non-Linear Response of a Fabry-Perot Cavity.

Measurement of Chirp Parameter of Intensity Modulator by Fiber Frequency Response Method

The Echo-Induced Influence on the Frequency-Modulating Calibration of the 3×3 Coupler-Based Michelson Interferometer and Its Suppression

A high linear silicon Mach-Zehnder modulator by the dual-series architecture

Machine-Learning-Assisted Instantaneous Frequency Measurement Method Based on Thin-Film Lithium Niobate on an Insulator Phase Modulator for Radar Detection

Coherent Detection-Based Automatic Bias Control of Mach–Zehnder Modulators for Various Modulation Formats

Compact Multi-Tone Microwave Photonic Frequency Measurement Based on a Single Modulator and Frequency-to-Time Mapping