Abstract:For advanced performance lithium-ion batteries (LIBs) various novel electrode materials with high energy density have been extensively investigated. Cobaltosic oxide (Co3O4), commonly used as an anode in LIBs, has attracted much interest because of its high theoretical specific capacity (890 mAh center dot g(-1)), high tap density, and stable chemical properties. However, its practical use has been hindered because of its low electronic conductivity and poor rate capability. To address these problems, we investigated a liquid phase precipitation method followed by thermal treatment and obtained a unique lamellar Co3O4 powder. Its X-ray diffraction (XRD) diffraction peaks match the standard pattern for cubic phaseCo(3)O(4) with good crystallinity. We found that the Co3O4 powder consists of many irregular sheets (1.5-3.0 mu m in diameter, 100-300 nm in thickness) with numerous poles by scanning electronmicroscopy (SEM). Additionally, the surface area was about 30.5m(2) center dot g-1, and this was calculated from BET nitrogen adsorption isotherm measurement data. Remarkably, perfect performance was obtained as evaluated by electrochemical measurements, including a high initial discharge capacity (1444.5 mAh center dot g(-1) at 0.1C) and excellent capacity retention (charge capacity after 50 cycles was still greater than 1100.0 mAh center dot g(-1) at 0.1C). However, its rate capability was still not adequate (75.3% of the first charge capacity after 50 cycles at 1C). To improve the rate capability, commercial carbon nanotubes (CNTs) mixed with the Co3O4 powder was used to enhance the electronic conductivity. The charge capacity retention ratios were 96.3% after 70 cycles at 1C and 97.0% after 50 cycles at 2C. Therefore, enhanced electrochemical performance with impressive rate capability was obtained, as expected.

Solvents adjusted pure phase CoCO3 as anodes for high cycle stability

Metal-organic Frameworks-Derived CoMOF-D@Si@C Core-Shell Structure for High-Performance Lithium-Ion Battery Anode

Synthesis and Modification of a Lamellar Co3O4 Anode for Lithium-Ion Batteries

High Lithium Storage of Co3O4 Enabled by Integrating Hollow and Porous Carbon Scaffolds

Facile Synthesis of Ultrasmall CoS2Nanoparticles Within Thin N-Doped Porous Carbon Shell for High Performance Lithium-Ion Batteries

Surface Design with Cation and Anion Dual Gradient Stabilizes High‐Voltage LiCoO2

High-Entropy Surface Complex Stabilized LiCoO<sub>2</sub> Cathode

Different Solid Electrolyte Interface and Anode Performance of CoCO3 Microspheres Due to Graphene Modification and LiCoO2||CoCO3@rGO Full Cell Study

Surface Design with Cation and Anion Dual Gradient Stabilizes High-Voltage LiCoO<sub>2</sub>

Stable cycling and low-temperature operation utilizing amorphous carbon-coated graphite anodes for lithium-ion batteries

Enhancing the Electrode Performance of Co3O4 Through Co3O4@a-TiO2 Core–shell Microcubes with Controllable Pore Size

Hierarchical Co2VO4 Yolk-Shell Microspheres Confined by N-doped Carbon Layer As Anode for High-Rate Lithium-Ion Batteries

High‐Entropy Surface Complex Stabilized LiCoO2 Cathode

Three-dimensional porous N-doped graphitic carbon framework with embedded CoO for ultrahigh and stable lithium storage

EDTA-Co(II) sodium complex derived Co(OH)2/Co3O4/Co nanoparticles embedded in nitrogen-enriched graphitic porous carbon as lithium-ion battery anode with superior cycling stability

In-Situ Constructed Protective Bilayer Enabling Stable Cycling of LiCoO 2 Cathode at High-Voltage

Constructing ZnCo2O4@CTP microspheres as a high-energy lithium storage material

Carbon coated porous Co3O4 polyhedrons as anode materials for highly reversible lithium-ion storage

Enhancing Co/Co2VO4 Li-ion Battery Anode Performances Via 2D-2D Heterostructure Engineering.

Nanoporous CoO Nanowire Clusters Grown on Three‐Dimensional Porous Graphene Cloth As Free‐Standing Anode for Lithium‐Ion Batteries

Improved Stability of Single‐Crystal LiCoO2 Cathodes at 4.8 V through Solvation Structure Regulation