Allan N. Kolek,Sophia R. Cooper,Kristopher D. Behler,Anindya Ghoshal,Tucker W. Moore,Andrew J. Wright,Victoria L. Blair,Richard F. Reidy,Marcus L. Young,Andrey A. Voevodin,Samir M. Aouadi,A. Kolek,S. R. Cooper,K. D. Behler,A. Ghoshal,T. W. Moore,A. J. Wright,V. L. Blair,R. F. Reidy,M. L. Young,A. A. Voevodin,S. M. Aouadi

Abstract:Effective thermal insulation materials rely on the fabrication of dense, ultra‐high‐temperature ceramics that can withstand harsh environments. Hafnium carbide‐based ceramics are one of the leading materials that have the potential to perform relatively well in high temperature oxidizing environments under mechanical loading due to their thermal and mechanical stability. In this study, we explore the effects of processing conditions to create dense, ablation‐resistant HfC‐SiC composites with a fixed composition of HfC‐20 wt.% SiC using a hot‐pressing method. Sintering pressure, temperature and time were varied and the material's relative density, phase composition, morphology, microstructure, and hardness were investigated. Composite ceramics with 99 % relative density relative to a theoretical value were created by hot pressing at 2100°C for one hour at 50 MPa and displayed a fine microstructure with an average grain size of ∼ 5 μm and a Vickers hardness of 22.9 ± 0.8 GPa. The mass loss was determined using an oxyacetylene torch with cross‐section investigations of oxide surface formations and subsurface microstructure changes. These HfC‐SiC samples developed a 410 nm hafnium oxide layer on the surface upon torch exposure and had an average calculated recession rate of 0.028 μm/s. This article is protected by copyright. All rights reserved

Low‐temperature reactive hot‐pressing of Ta0.2Hf0.8C‐SiC ceramics at 1700°C

Microstructure and mechanical behavior of TaxHf1−xC–SiC fabricated by reactive hot‐pressing: Effect of Ta:Hf ratio

Low temperature sintering of Hf0.95Nb0.05B2-based ceramics with submicron-scaled grains and enhanced mechanical properties

Rapid densification and mechanical properties of ultra-high-pressure sintered transition metal carbide ceramics

Low temperature densification mechanism and properties of Ta1-Hf C solid solutions with decarbonization and phase transition of Cr3C2

Pressureless sintering and properties of (Hf0.2Zr0.2Ta0.2Nb0.2Ti0.2)C high-entropy ceramics: The effect of pyrolytic carbon

High temperature ablation of hot pressed HfC‐SiC ceramics

Strengthening Hf0.95Ta0.05B2 Ceramic With Ultrafine Grains and High-density Dislocations

Low-temperature densification of high-entropy (Ti,Zr,Nb,Ta,Mo)C—Co composites with high hardness and high toughness

Low temperature fabrication of highly dense α‐Si3N4 ceramics

Densification and joining of a (HfTaZrNbTi)C high-entropy ceramic by hot pressing

Polymer-derived SiHfN ceramics: From amorphous bulk ceramics with excellent mechanical properties to high temperature resistant ceramic nanocomposites

Properties and Microstructure of an HfB2-HfC-SiC Ultra High Temperature Ceramics

Novel (Zr, Ti)(C, N)–SiC ceramics via reactive hot-pressing at low temperature

Densification, Microstructure and Mechanical Properties of Ta4HfC5-based Ceramics Obtained from Synthesized Nanoscale Powder

Densification, Microstructure and Mechanical Properties of Multicomponent (tizrhfnbtamo)c Ceramic Prepared by Pressureless Sintering

Investigation of the microstructure and physical properties of TaSi 2 sintered at high temperature and high pressure

Microstructure evolution of ultra-fine grained HfC ceramics with high hardness sintered under ultrahigh pressure by plastic deformation densification mechanism

Pressureless densification of HfB2-based ceramics using HfB2 powders by borothermal reduction

Microstructures and mechanical properties of high-entropy (Ti0.2Zr0.2Hf0.2Nb0.2Ta0.2)C ceramics with the addition of SiC secondary phase

High‐strength medium‐entropy (Ti,Zr,Hf)C ceramics up to 1800°C