Abstract:We demonstrated remarkably enhanced 2.7 mu m emission in glass-ceramic (GC) fibers containing NaYF4: Er3+ nanocrystals with 980 nm excitation for the first time. The melt-in-tube technique is of scientific and technical significance for the fabrication of GC fibers in comparison to the conventional rod-in-tube technique. The obtained precursor fibers, in which the structure can be maintained well, exhibit no obvious element diffusion or crystallization during the fiber-drawing process. After a careful heat treatment, NaYF4 nanocrystals were controllably precipitated in the glass fiber core. Owing to the incorporation of Er3+ ions into the low phonon energy NaYF4 nanocrystals, enhanced 2.7 mu m emission was achieved from the Er3+-doped GC fibers, which was almost undetectable in precursor fibers due to the high phonon energy of the borosilicate glass fiber matrix. Moreover, the 2.7 mm emission lifetime was obtained due to the excellent emission properties of Er3+ in the GC fibers. The transmission loss values of precursor fibers and GC fibers at 1310 nm were measured to be 7.44 dB m(-1) and 11.81 dB m(-1), respectively. In addition, a theoretical simulation based on the rate equations and propagation equations was performed to evaluate the possibility of 2.7 mu m laser output. The excellent optical properties endow the GC fibers with potential applications for mid-infrared fiber lasers.

Paving way for fabrication of silica-based single -frequency seed laser: Ultrahighly Yb-doped optical fibers via sol-gel method combined with silica tube inner wall coating and fusion-tapering technique

Low-Threshold Microlaser in Er : Yb Phosphate Glass Coated Microsphere

High ytterbium concentration Yb/Al/P/Ce co-doped silica fiber for 1-μm ultra-short cavity fiber laser application

Femtosecond Mode-locked Fiber Laser at 1 Μm Via Optical Microfiber Dispersion Management

Efficient three-level continuous-wave and GHz passively mode-locked laser by a Nd3+-doped silicate glass single mode fiber

Preparation of Er:YAG Crystal-Derived All-Glass Silica Fibers For a 1550-nm Single-Frequency Laser

Multi‐component yttrium aluminosilicate ( YAS ) fiber prepared by melt‐in‐tube method for stable single‐frequency laser

Yb-Doped Aluminophosphosilicate Laser Fiber

Over 100 mW linearly polarized single-frequency fiber laser based on Er:YAG crystal-derived silica fiber

High quantum efficiency and high concentration erbium-doped silica glasses fabricated by sintering nanoporous glasses

High-power, high-efficiency single-frequency DBR fiber laser at 1064 nm based on Yb3+-doped silica fiber

Spectroscopic and Laser Properties of Al-P Co-Doped Yb Silica Fiber Core-Glass Rod and Large Mode Area Fiber Prepared by Sol-Gel Method

Single-frequency DBR lasing by integrating FBGs into germanium-free photosensitive highly Yb3+-doped silica fibers

Sub-kHz linewidth 1.6-μm single-frequency fiber laser based on a heavily erbium-doped silica fiber

High-power Lasing at 900 Nm in Nd3+-doped Fiber: a Direct Coordination Engineering Approach to Enhance Fluorescence

Efficient and Broadband Emission in Dy3+-Doped Glass-Ceramic Fibers for Tunable Yellow Fiber Laser

Precisely controllable fabrication of Er3+-doped glass ceramic fibers: novel mid-infrared fiber laser materials

Controllable fabrication of novel all solid-state PbS quantum dot-doped glass fibers with tunable broadband near-infrared emission

A novel route to fabricate Yb:YAG ceramic fiber and its optical performance

Efficient single-frequency Tm:YAG crystal-derived silica fiber laser at 1.7 μm

4.8-μm CO-filled hollow-core silica fiber light source