Abstract:In the development of advanced steel, accurate and detailed knowledge about the kinetics of phase transformations and microstructure formation is critical. The critical issue in pearlite-austenite transformation is the consideration of diffusional paths of the alloy element. Simulation has been an available method to study the diffusion of alloy elements and the migration rate of the phase boundary in the complex morphological evolution of austenite growth. The isothermal pearlite-austenite transformations at 720 and 740 degrees C in Fe-0.6%C-2%Mn (mass fraction) alloy were studied by phase-field methods based on MICRESS. At different temperatures, the effects of diffusional paths on the austenite transformation were discussed. To achieve a semiquantitative verification of the simulated results, the migration rates of the austenite/pearlite boundary at 720 and 740 degrees C were estimated from the experimental kinetics curves by fitting the JMA equation. By measuring the Mn profile in austenite, the modes of the austenization at 720 and 740 degrees C can be verified as partitioned local equilibrium (PLE) and non-partitioned local equilibrium (NPLE) modes. The heterogeneous distribution of Mn in austenite at 740 degrees C can be observed with STEM-EDS. However, the homogenous distribution of Mn can be found near the pearlite/austenite boundary in austenite at 720 degrees C. The cases considering the gamma, alpha, and interface-diffusional paths were simulated by phase-field methods to compare with the migration rates of the austenite/pearlite boundary. Because carbon is an interstitial element in steel and has an interstitial diffusional mechanism, it can be speculated reasonably that the diffusion of C mainly proceeded in austenite and ferrite through the considerations of the atom-size of carbon and the experimental results. Phase-field methods were used to study Mn diffusion in the lamellar pearlite-austenite transformation. With the analysis of the experimental estimations, the interface-diffusional path was observed as the dominant path for the Mn diffusion. It is because the Mn atoms have greater diffusivity in interfaces than in gamma or alpha-diffusional paths. Furthermore, the diffusional activation energy is closely related to the diffusivity of Mn at the interface. Moreover, compared with the gamma-diffusional path, the diffusional flux of Mn in ferrite is much larger than that in austenite. Thus, it can be concluded that the contribution of the alpha-diffusional path to the migration rate of the pearlite/austenite boundary is larger than that of the gamma-diffusional path. As a result, considering the alpha-diffusional path in the thermodynamics analysis under NPLE mode makes more sense. However, ignoring the interface- and alpha-diffusional path, which is different from the traditional cognition in PLE mode, will result in a magnitude error for the thermodynamics analysis.

Development of Fully Pearlitic Microstructure in a Hypoeutectoid Steel

Heterogeneous Multiphase Microstructure Formation through Partial Recrystallization of a Warm-Deformed Medium Mn Steel during High-Temperature Partitioning

Investigation of Austenitization During Continuous Heating Process in Hypereutectoid Steels

Simulation of lamellar pearlite growth morphology with phase-field method

Effects of austenitization and cooling rates on the microstructure in a hypereutectoid steel

Dilatometric and Microstructural Investigations on Austenite Decomposition under Continuous Cooling Conditions in a Cu-Bearing High-Strength Low-Alloy Steel

EFFECTS OF AUSTENITIZATION AND COOLING RATESON THE MICROSTRUCTURE IN A HYPER-EUTECTOID STEEL

Phase transformation and microstructure evolution of pearlite heat-resistant steel during heating

Diffusional and displacive transformations in interstitial-free steel within the scope of a critical assessment of the mechanical property

Study on the Nucleation and Growth of Pearlite Colony and Impact Toughness of Eutectoid Steel

Volume Fractions of Proeutectoid Ferrite/Pearlite and Their Dependence on Prior Austenite Grain Size in Hypoeutectoid Fe-Mn-C Alloys

Shaping mechanism of ultrafine metastable austenite in HSLA steels through a cumulative process of hot rolling, partitioning and tempering

Quenching and Partitioning (Q&P) Steel: Alloy Design, Phase Transformation and Evolution of Microstructure

Kinetic Transitions and Mn Partitioning During Austenite Growth from a Mixture of Partitioned Cementite and Ferrite: Role of Heating Rate

Development of significantly hard hypereutectoid plain carbon steel through incomplete austenitization based cyclic quenching treatmentEntwicklung eines signifikant harten übereutektoiden Kohlenstoff‐Glattstahls durch eine zyklische Abschreckung mit unvollständiger Austenitisierung

Atom-probe tomographic and dilatometric studies of phase-transformations after inter-critical annealing of a low-carbon dual-phase steel

Phase Field Study of the Diffusional Paths in Pearlite-Austenite Transformation

Progress in Effect of Alloying Element Partition on Thermodynamics and Kinetics of Pearlite Transformation and Its Austenitization

Early Martensitic Transformation in a 0.74C–1.15Mn–1.08Cr High Carbon Steel

Microstructure, mechanical properties and strengthening mechanism of high strength hot-rolled ferrite-martensite dual phase steel

Computational Thermodynamics/kinetics Aided Design for the Microstructure of Pearlitic Steels During Cooling Process