Abstract:The term Shear Transformation Zone (STZ) refers to the atomic cluster that dissipates external stress through cooperative shear. The STZ is the process that describes the local atomic rearrangement mechanism of metallic glasses (MGs). Based on the cooperative shear model (CSM), the size of an STZ has been estimated using the rate jump method (RJM), nano-scale creep method (NCM), first pop-in statistical method (FSM) and serration-flow statistic method (SSM), respectively. In the nanoindentation process, different sizes of STZs can be elicited by employing different experimental conditions (indentation depth and loading rate). In addition, different characterization methods exhibit various degrees of response to changes in the experimental conditions. In order to study the heterogeneity of the STZ of MGs using different nanoindentation methods, in this study, three types of Zr-based MGs with different Poisson's ratios were used as the research objects, and the sizes of the STZs of these amorphous alloys were calculated using the previously mentioned methods. By applying different maximum loads and loading rates, the effect of the nanoindentation test parameters on the size of the metallic glasses' STZs were characterized using different nanoindentation methods. Under the same testing conditions, the volume of the STZs was calculated using each method that exhibited improvement with the increase of the Poisson's ratio. The calculated results obtained using the RJM, NCM and SSM were found to be much greater than those obtained using the FSM. With the increase in the loading rate, the results obtained using NCM decreased, whereas the statistic method results slightly increased. At the maximum load, the STZ volume calculated using the JRM, NCM and SSM increased significantly. The FSM was not affected by the maximum load. Finally, these differences are discussed from the aspects of the calculation principles and the activation and evolution of the STZ.

Effect of Zr content on the strain rate sensitivity of nanohardness of Ti-Zr-Cu-Ni-Al thin film metallic glass

High Strain Rate Sensitivity of Hardness in Quinary Ti-Zr-Hf-Cu-Ni High Entropy Metallic Glass Thin Films

Effect of temperature and strain rate on deformation behavior in metallic glassy films

Effects of RF Magnetron Sputtering Power on the Mechanical Behavior of Zr-Cu-Based Metallic Glass Thin Films

Size dependent mechanical properties and deformation mechanisms in Ti and Zr films

Mechanical responses and plastic rheological behavior of Ti–Zr-Hf-Co-Ni-Cu metallic glass thin films deposited with different substrate temperatures during nanoindentation and nanoscratch process

Effect of Mechanical Strain on the Optical Properties of Nodal‐Line Semimetal ZrSiS

High strain rate in situ micropillar compression of a Zr-based metallic glass

High strain rate sensitivity of hardness in Ti-Zr-Hf-Be-(Cu/Ni) high entropy bulk metallic glasses

Effect of Strain Rate on Mechanical Deformation Behavior in CuZr Metallic Glass

The Effect of Free Volume on the Deformation Behaviour of a Zr-based Metallic Glass under Nanoindentation

Effects of nanoscale chemical heterogeneity on the wear, corrosion, and tribocorrosion resistance of Zr-based thin film metallic glasses

Effect of nanoindentation experimental parameters on the estimation of the plastic events in metallic glasses employing various analysis methods

Effects of substrate temperature on structure, thermal stability and mechanical property of a Zr-based metallic glass thin film

Strain rate-dependent hardness and deformation behavior in the nanocrystalline/amorphous Ti2AlNb film

Effect of Loading Rate on Creep Behavior and Shear Transformation Zone in Amorphous Alloy Thin Films, and Its Correlation with Deformation Mode Transition

Improved Tensile Ductility by Severe Plastic Deformation for Nano-Structured Metallic Glass.

Nanoindentation and relaxation behavior of nitrogen doped zirconium based bulk metallic glass

Indentation Size Effects of Mechanical Behavior and Shear Transformation Zone in Thin Film Metallic Glasses

Effect of Applied Stress on the Mechanical Properties of a Zr-Cu-Ag-Al Bulk Metallic Glass with Two Different Structure States

Design of amorphous-nanocrystalline films of TiAlCrNbZr x multi-component alloy: The effect of Zr on the corrosion resistance and mechanical properties