Abstract:Semiconductor micro-chips with critical dimensions of 50 nm and below will likely be manufactured with extreme ultraviolet (EUV) lithography at a wavelength of 13.5 nm. Among others EUV lithography requires a brilliant radiation source with output power between 50W and 120W collected in an intermediate focus at the entrance of the exposure tool. The development of these powerful EUV sources will have spin-off products for applications related to inspection and quality control in lithography related industry. We also expect numerous applications in microand nano-machining and –processing as well as microscopy at shortest wavelengths. In the present paper experimental results of both laser produced plasma and gas discharge produced plasma EUV source development at XTREME technologies – the EUV joint venture of Lambda Physik AG, Goettingen, and Jenoptik LOS GmbH, Jena, Germany – are presented. Source characterization has been performed with calibrated metrology tools for measurement of energy, power, size, spectra and stability of the EUV emission. The laser plasma investigations are performed with a 1st experimental facility comprising a commercial 40W Nd:YAG laser coupled to a liquid xenon-jet target system, which was developed by XTREME technologies. The EUV in-band power emitted from the 0.25mm diameter plasma into 2π solid angle is 0.2W, the conversion efficiency amounts 0.5%. Estimated EUV emission parameters using a 500W laser for plasma generation are discussed. The gas discharge EUV sources described here are based on efficient Xenon Z-pinches. In the 3rd prototype generation the plasma pinch size and the available emission angle have been matched to the etendue of the optical system of 2–3mm2. The solid angle of emission from the pinch of 1.3mm ×1.5mm amounts 1.8 sr. The Z-pinch EUV source can be operated continuously at 1000 Hz with an in-band output power of 10W in 1.8 sr. This corresponds to 4.5W in intermediate focus, if no spectral purity filter is needed. The power emitted into a solid angle of 2π sr is 35W. Emission energy stability ranges between 1% and 4% standard deviation. Spectral, temporal as well as spatial emission characteristics of the discharge source in dependence on the gas discharge geometry have been evaluated. The potentials as well as limits for power scaling of the two technological source concepts and potential application areas of EUV radiation at 13.5 nm and XUV radiation between 1 nm and 80 nm in microand nano-processing and inspection are discussed.

Modeling the hundreds-of-nanoseconds-long irradiation of tin droplets with a 2 extmu m-wavelength laser for future EUV lithography

Physics of laser-driven tin plasma sources of EUV radiation for nanolithography

High-energy ions from Nd:YAG laser ablation of tin microdroplets: comparison between experiment and a single-fluid hydrodynamic model

Extreme ultraviolet light sources: State of the art, future developments, and potential applications

Characterization of angularly resolved EUV emission from 2-$μ$m-wavelength laser-driven Sn plasmas using preformed liquid disk targets

Influence of CO2-laser pulse parameters on 13.5 nm extreme ultraviolet emission features from irradiated liquid tin target

Expansion Dynamics After Laser-Induced Cavitation in Liquid Tin Microdroplets

Generation of the small tin droplet streams with a manipulable droplet spacing via the forced velocity perturbation

Ion distribution and ablation depth measurements of a fs-ps laser-irradiated solid tin target

EUV Debris Mitigation using Magnetic Nulls

Simulation of extreme ultraviolet radiation of laser induced discharge plasma

Experimental Study on the Temporal Evolution Parameters of Laser–Produced Tin Plasma under Different Laser Pulse Energies for LPP–EUV Source

A Laser-Produced Plasma Source Based on Thin-Film Gd Targets for Next-Generation Extreme Ultraviolet Lithography

Influence of a laser intensity on EUV brightness and ion speed from a laser-assisted discharge-produced plasma

Elastic scattering cross sections and transport of tin ions in extreme ultraviolet lithography sources

Monte Carlo/molecular Dynamics Simulation on Melting and Evaporating Processes of Material Due to Laser Irradiation

Molecular Dynamics Simulation Of Ultra-Fast Thermal Transition In Thin Foil Irradiated By High Power Ultra-Short Laser

Numerical Analysis of Ultrashort Pulse Laser-Induced Thermomechanical Response of Germanium Thin Films

Accurate Two-Dimensional Simulation Model and Experimental Demonstration in Ultraviolet Picosecond Laser Scribing Ablation

Laser Etching Processes : Towards Sub-Picosecond X-UV Irradiation

Tin removal by an annular surface wave plasma antenna in an extreme ultraviolet lithography source