Abstract:Fe-Si-B-P-Cu nanocrystalline alloy were treated with ball-mill using a lubricant as a process control agent (PCA). The resulting alloy powder is a strong candidate material for soft magnetic composites. Two ball milling methods (continuous and interval) were employed to control the interactions between the PCA and the alloy surface, and their effect on the microstructure of the prepared alloy particles was investigated. The alloy sheet was broken into small pieces and deformed plastically into flake-shaped particles regardless of the ball milling method implemented. Friction-force microscopy of the alloy immersed in the PCA revealed that the friction coefficient of the alloy surface exposed to air for a certain period was higher than that of the unexposed alloy surface (immediately after polishing). During ball milling, the ratio of the newly generated surface to the oxidized surfaces of the alloy subjected to interval milling was smaller than that of the alloy subjected to continuous milling. Therefore, the friction coefficient of the surface of the alloy subjected to interval milling was higher than that of the alloy subjected to continuous milling. Synchrotron radiation analysis revealed that the alloy subjected to interval milling exhibited enhanced surface friction, showing an obvious steepness and inflection in the diffraction intensity as a function of the tilt angle based on the Schulz reflection method. This indicates formation of crystallographic texture in α-Fe grains in an amorphous matrix. Hence, we demonstrated successfully that the ball milling process induced a crystallographic texture in the Fe-based nanocrystalline alloy due to plastic deformation due to the enhanced surface friction. The surface of the alloy was prepared based on the effect of the interfacial interactions between the alloy surface and the PCA.

Improving carbon nanotube dispersion in aluminum matrix composite powders by a repeating-deformation ball milling process

Long-term Ball Milling and Hot Pressing of In-Situ Nanoscale Tungsten Carbides Reinforced Copper Composite and Its Characterization

Microstructure and Properties of In-Situ TiC Reinforced Copper Nanocomposites Fabricated Via Long-Term Ball Milling and Hot Pressing

Unraveling the dispersion mechanism of carbon nanotubes in aluminum powder particles during high energy ball milling by FIB-TEM study

Evolution of Microstructure and Mechanical Properties of CNTs/Al-Mg Composites Prepared by Powder Metallurgy

Balanced strength and ductility in CNT/Al composites achieved by flake powder metallurgy via shift-speed ball milling

Mechanical properties of the Al-Mg/MWCNTs composite powders: The effects of ball milling process parameters

Smart Mechanical Powder Processing for Producing Carbon Nanotube Reinforced Aluminum Matrix Composites

Al/CNT nanocomposite fabrication on the different property of raw material using a planetary ball mill

Mechanical milling and its influence on microstructure and electric conductivity of high mass fraction TiC / Cu composites

Influencing the Size and Shape of High-Energy Ball Milled Particle Reinforced Aluminum Alloy Powder

Synthesis of carbon nanotube reinforced Al matrix composite coatings via cold spray deposition

Study on the Properties of Carbon Nanotube (CNTs) Reinforced AlSi10Mg Composites Fabricated by Powder Metallurgy

Towards Homogeneous Distribution of Coarse Grain in a Tri-Modal Al-based Composites Utilizing Localized Grain Growth

Powder preparation during ball milling and laser additive manufacturing of aluminum matrix nanocomposites: Powder properties, processability and mechanical property

Tailoring the structure and mechanical properties of graphene nanosheet/aluminum composites by flake powder metallurgy via shift-speed ball milling

Improvement of interfacial interaction and mechanical properties in aluminum matrix composites reinforced with Cu-coated carbon nanotubes

Effect of Increasing the Strength of Aluminum Matrix Nanocomposites Reinforced with Microadditions of Multiwalled Carbon Nanotubes Coated with TiC Nanoparticles

Fabrication of Nano-Sic_p/al Composite by High Energy Ball Milling

Effects of interfacial interactions between metal and process control agents during ball milling on the microstructure of the milled Fe-based nanocrystalline alloy powder

Nanoscale Dispersion of Carbon Nanotubes in a Metal Matrix to Boost Thermal and Electrical Conductivity via Facile Ball Milling Techniques