Abstract:In the conventional wet slurry method for making lithium-ion battery (LIB) electrodes, unwanted N-Methyl-2-Pyrrolidone (NMP) solvent is used. The use of NMP increases the overall energy demand during electrode coating since NMP needs to be dried from the coated slurry and recovered. The improper use of NMP can also impose detrimental effects on health and the environment. Thus, solvent-free dry processes are gaining increased interest worldwide for electrode fabrication. Amongst different dry electrode manufacturing techniques, electrostatic spray deposition (ESD) is one of the most promising techniques. In this study, positive LiNi0.8Co0.1Mn0.1O2 (NMC811) electrodes were manufactured by the ESD process and wet slurry process. The differences between the electrodes made by these two processes were investigated by the peel strength test, electrochemical techniques (e.g., rate tests, electrochemical impedance spectroscopy, and constant voltage/constant current cycling), scanning electron microscopy with energy dispersive x-ray spectroscopy, and X-ray photoelectron spectroscopy. In the dry electrodes, most active material particles were densely covered by the binder and conductive agents. Whereas in wet slurry electrodes, binder and conductive agents were distributed more homogenously both on the active material surfaces and between the active material particles. The uniform distribution of the binder and conductive agents in the slurry electrodes results in a robust conductive network, leading to better performance at high C- rates (e.g., 2-5C). Interestingly, the dry electrodes had comparable performance to slurry electrodes at the initial stages of electrochemical testing with low current rates. Hence, it can be concluded that the distribution of the electrode materials affects active material usage and the conductive paths, and a homogenous distribution is needed to achieve faster discharge capacity at higher C rates. Future work will focus on the long-term cycling performance of the electrodes to further understand the degradation mechanisms and differences between the two types of electrodes.

Benchmarking the Performance of Moisture-Sensitive Battery Materials: the Importance of the Electrode Preparation Method

Ton-scale preparation of single-crystal Ni-rich ternary cathode materials for high-performance lithium ion batteries

Electrochemical performance and thermal stability analysis of LiNixCoyMnzO2 cathode based on a composite safety electrolyte

Exploration of PVP-Combustion Synthesis and Electrochemical Performance of O3-type NaxNi0.33Fe0.33Mn0.33O2 Layered Material for Sodium-Ion Batteries

Systematic Optimization of Battery Materials: Key Parameter Optimization for the Scalable Synthesis of Uniform, High-Energy, and High Stability LiNi 0.6 Mn 0.2 Co 0.2 O 2 Cathode Material for Lithium-Ion Batteries

Preparation of NCM622 cathode materials using nanoscale porous NiO material

Tuning Na Occupation and Annealing Temperature on Na Diffusion Pathways in P2-Type NaxNi0.25Mn0.75O2 for Sodium-Ion Batteries by Ab Initio Calculations

Synthesis and microstructure characterization of Li[Ni1/3Mn1/3Co1/3]O2for lithium ion batteries cathode

Investigating the Influence of Three Different Atmospheric Conditions during the Synthesis Process of NMC811 Cathode Material

Synthesis and design of NaNi1/3Fe1/3Mn1/3O2 cathode materials for long-life sodium-ion batteries

Preparation and Property Optimization of High Capacity O3-type NaNi0.4Fe0.2Mn0.4O2

Boosting the Electrochemical Performance and Moisture Stability of O3-type NaNi1/3Fe1/3Mn1/3O2 Cathodes using Novel Na2MoO4 Coatings Prepared via a Polyvinylpyrrolidone-anchored Complex Coating Process

A Two-Step Surface Modification Optimization for Performance Recovery of NaNi 0.33 Fe 0.33 Mn 0.33 O 2

Study of degradation mechanisms in aqueous-processed Ni-rich cathodes for Enhanced Sustainability of Batteries

High-rate Performance of LiNi0.5Mn1.45Al0.05O4 Cathode Material for Lithium-Ion Batteries

Investigating the Structure and Performance Differences between the Electrodes Made by a Dry and a Wet Slurry Processes

Toward Greener Lithium-Ion Batteries: Aqueous Binder-Based LiNi0.4Co0.2Mn0.4O2 Cathode Material with Superior Electrochemical Performance

An Efficient Synthetic Method To Prepare High-Performance Ni-Rich Lini0.8co0.1mn0.1o2 For Lithium-Ion Batteries

Greener, Safer and Better Performing Aqueous Binder for Positive Electrode Manufacturing of Sodium Ion Batteries

Optimizing Electrochemical Performance in Sodium-Ion Batteries Using O3-type Na0.90Cu0.22Fe0.30Mn0.48O2 and Hard Carbon

Understanding the Effects of the Mixing Processes on the Performance of NMC-LMO Blend Electrodes Made by a Dry Electrostatic Spray Deposition Process