Abstract:Layered O3 type oxides exhibit promising prospects as high-performance cathodes for sodium-ion batteries (SIBs) due to their low cost and high theoretical capacities. Nevertheless, the intrinsic surface composition and bulk structure degradation upon cycling presents a huge obstacle to stable sodium-ion storage/transportation. Besides, the effective surface decoration on layered O3 oxides is still challenging through conventional wet chemical route owing to their extraordinarily high surface sensitivities. Herein, a typical O3 type layered oxide of NaNi0.5Mn0.5O2 (NNMO) was selected and successfully encapsulated by precisely controlled Al2O3 layers via atomic layer deposition (ALD) technology. With the optimally controlled Al2O3 thickness of 3 nm, the surface regulated NNMO delivers a highly reversible capacity of 73.6 mA h g-1, with a significantly improved capacity retention of 68.0% after 300 cycles at 0.5 C, and a superior rate capability of 65.8 mA h g-1 at 10 C. Further air sensitivity tests demonstrate that the protective layer could effectively mitigate the generation of sodium-based impurities on NNMO, and reduce the surface sensitivities. Both chemical and electrochemical aging tests confirm the contribution of Al2O3 coating layer in alleviating ion dissolution as well as stabilizing the structure and morphology of NNMO. Based on regulating the surface of O3 type layered oxides utilizing ALD technique, this work supplies an effective and facile strategy to overcome the challenges from fast structure degradation and electrochemical property decay, which not only highlights the significance and effectiveness of surface engineering in secondary batteries, but also sheds light on accurate interface construction and regulation for active electrode materials, particularly for those sensitive to ambient atmosphere.

Boosting the Electrochemical Performance and Moisture Stability of O3-type NaNi1/3Fe1/3Mn1/3O2 Cathodes using Novel Na2MoO4 Coatings Prepared via a Polyvinylpyrrolidone-anchored Complex Coating Process

Boosting fast ionic transport and stability of O3-NaNi1/3Fe1/3Mn1/3O2 cathode via Al/Cu synergistically modulating microstructure for high-rate sodium-ion batteries

Suppressing Phase Transition and Improving Electrochemical Performances of O3-NaNi1/3Mn1/3Fe1/3O2 Through Ionic Conductive Na2SiO3 Coating

Zr-doped O3-type NaNi1/3Fe1/3Mn1/3O2 Cathodes with Enhanced Structure Stability for Sodium-Ion Batteries

Enhanced Cycling Stability and Rate Capability of Al2O3-Coated NaNi1/3Fe1/3Mn1/3O2 Cathodes for Sodium-Ion Batteries

O3-Type Na 0.95 Ni 0.40 Fe 0.15 Mn 0.3 Ti 0.15 O 2 Cathode Materials with Enhanced Storage Stability for High-Energy Na-Ion Batteries

Designing Air-Stable O3-Type Cathode Materials by Combined Structure Modulation for Na-Ion Batteries.

Topography Control and Component Design Strategies to Enhance Electrochemical Performance of O3-Type Cathode Materials for Sodium-ion Batteries

Molybdenum Incorporated O3‐type Sodium Layered Oxide Cathodes for High‐Performance Sodium‐Ion Batteries

Facile design and synthesis of Co-free layered O3-type NaNi0.2Mn0.2Fe0.6O2 as promising cathode material for sodium-ion batteries

Exploration of PVP-Combustion Synthesis and Electrochemical Performance of O3-type NaxNi0.33Fe0.33Mn0.33O2 Layered Material for Sodium-Ion Batteries

Enhanced Na-storage properties of O3-type NaNi0.5Mn0.5O2 cathodes by doping and coating dual-modification strategy

Suppression of Monoclinic Phase Transitions of O3-Type Cathodes Based on Electronic Delocalization for Na-Ion Batteries

Prompting structure stability of O3–NaNi0.5Mn0.5O2 via effective surface regulation based on atomic layer deposition

Enhancing the Cycling and Rate Performance of NaNi 1/3 Fe 1/3 Mn 1/3 O 2 Cathodes by La/Al Codoping

Toward high stability of O3‐type NaNi1/3Fe1/3Mn1/3O2 cathode material with zirconium substitution for advanced sodium‐ion batteries

High-entropy configuration of O3-type layered transition-metal oxide cathode with high-voltage stability for sodium-ion batteries

Elucidating the Structural Evolution of O3-type NaNi1/3Fe1/3Mn1/3O2: A Prototype Cathode for Na-Ion Battery.

Defensive and Ion Conductive Surface Layer Enables High Rate and Durable O3‐type NaNi1/3Fe1/3Mn1/3O2 Sodium‐Ion Battery Cathode

NaTi2(PO4)3 modified O3-type NaNi1/3Fe1/3Mn1/3O2 as high rate and air stable cathode for sodium-ion batteries

Enhanced stability and electrochemical performance of O3-type NaNi1/3Fe1/3Mn1/3O2 cathode material via yttrium doping for advanced sodium-ion batteries