Abstract:Several ASTM standards on the fracture of glued and welded joints need attention because they do not consider the Griffith energy criterion of cracking which was proposed a century ago. It is almost as if Griffith never existed because the ASTM definition of failure is the stress criterion postulated by Galileo in 1638 in which stress at failure (i.e. strength = force/area) is defined as the determinant of fracture. Irene Martinez Villegas (Villegas, Rans 2021 Phil. Trans. R. Soc. A 376, 20200296. ( doi:10.1098/rsta.2020.0296 )) shows in this volume that attempts to use ASTM D5868 to standardize welded composite (carbon fibre reinforced polymer, CFRP) lap joints reveal major problems. First, the test is a low angle bend–peel test; not shear. Second, the energy required to break the joint is not emphasized so that joints may have high strength properties but also low toughness; third, the fracture force is not proportional to the lap joint area so the concept of strength independent of sample size is false; fourth, as the CFRP panels are made thicker, the strength rises at constant overlap area so the strength can be any value you want; fifth, the strength of larger joints goes down; this is the size effect noted in many bend-cracking tests, much as Galileo suggested for bent beam fracture in his famous book ‘the larger the machine, the greater its weakness'. The purpose of this paper is to demonstrate that poor ASTM ‘shear strength’ standards should be replaced by a definition of welded lap joint performance based on Griffith's energy conservation argument in which fracture surface energy is the main parameter resisting failure. The foundation of this Griffith-style lap joint analysis for long cracks goes back to 1975 but has been largely ignored until now because it does not fit the Griffith equation for cracked sheets, has no ‘stress intensity factor’, and travels at constant speed, not accelerating like the standard Griffith tension crack. This study of tensile delamination shows that a long lap crack is not driven by stress near the crack but by changes in stored elastic energy in the stretched strips remote from the crack tip, while strain energy release rate is negative. It would be more appropriate to call this lap failure a tensile delamination crack. This article is part of a discussion meeting issue ‘A cracking approach to inventing new tough materials: fracture stranger than friction’.

Estimating the remaining service life of in-situ grouted post-tension anchors using flaw tolerance limit plots

Fatigue Damage Development of Grouted Connection under Varying Cyclic Loading

Energizing ASTM lap joint fracture standards

Experimental Testing of Grouted Posttensioned Anchors with High Rod-to-Duct Area Ratios

Experimental and Numerical Study of Corrugated Anchors for CFRP Plates

Consistent time-to-failure tests and analyses of adhesive anchor systems

Numerical Model of Cumulative Damage Evolution of Offshore Wind Turbine Grouted Connection under Cyclic Axial Load

Crack propagation, failure and ultimate load capacity of the grout layer in the prestressed anchor bolt foundation of wind turbine tower

Variation Characteristics of Key Dynamic Measurement Signals of Anchor Bolts with Different Anchorage Qualities under Pull-out Loads

Bond and re‐anchoring tests of post‐tensioned steel tendon in case of strand failure inside cement grouting with voids

An Innovative Approach to Reduce Bursting and Spalling Stresses at Anchorage Zone of Post-Tensioned Member Incorporating Different Types of Reinforcement Configuration

Stress analysis of full-length grouted bolt under shear deformation of anchor interface

Acoustic emission parametric analysis to investigate the damage evolution of anchor systems designed by the concrete capacity design method

Experimental Study on Anchorage Mechanical Behavior and Surface Cracking Characteristics of a Non-persistent Jointed Rock Mass

Study on the anchoring performance and failure mechanism of basalt/glass hybrid fiber reinforced plastic anchors in coupled environment

Experimental investigation on connection performance of fully-grouted sleeve connectors with various grouting defects

Horizontal Cracking and Crack Repair Analysis of a Super High Arch Dam Based on Fracture Toughness

Probabilistic Design Analysis of Plate Anchors in Spatially Variable Clay

Development of an anchor system for thick CFRP plates: Experimental and numerical investigation

In-Situ Test and Numerical Simulation of Anchoring Performance of Embedded Rock GFRP Anchor

Creep rate based time to failure prediction of adhesive anchor systems under sustained load