Abstract:The strength of prestressed steel strands has developed towards high strength, increasing from 1860 MPa to over 2200 MPa. The stress in the prestressed anchorage zone is more concentrated and complex, and the anchor plates for dispersed loads need to be optimized in design. This article proposes a design scheme for adding a middle pressure-bearing step based on the existing anchor plate and then establishes a 1/4 model of the concrete anchoring area of the anchor plate for finite element analysis. Based on the theory of the strut-and-tie model, the position of the middle pressure-bearing step is determined according to the maximum angle of the strut-and-tie model. Then, carry out force transfer tests in the anchorage zone for verification. The research results indicate that after adding a middle pressure bearing step to the anchor plate, the angle between the strut-and-tie model in the anchorage zone increases, and the bearing capacity improves. The position of the middle pressure-bearing step in the anchor plate is different, and the angle between the strut-and-tie models is different. According to the middle step position parameter, λ (the ratio of the effective width of the middle step to the distance from the middle step to the end face of the anchor plate) is 0.533 to optimize the anchor plate, and the bearing capacity of its anchorage zone is relatively high. The main tensile and main compressive stresses of the anchor plate after optimization increased by 6.2% and 5.74%, respectively, compared to the anchor plate before optimization. The main tensile stress of the spiral reinforcement under the anchor plate decreased by 0.59%, the main compressive stress decreased by 2.89%, and the von-Mises stress decreased by 2.32%. The side surface tensile stress of concrete under the anchor plate was reduced by 4.3 percent. Finally, three concrete specimens were poured for force transfer testing in the anchorage zone, verifying the safety and reliability of the optimized anchor plate in the 2200 MPa-level prestressed anchorage zone.

An Innovative Approach to Reduce Bursting and Spalling Stresses at Anchorage Zone of Post-Tensioned Member Incorporating Different Types of Reinforcement Configuration

A Design Proposal for Concrete Cover Separation in Beams Strengthened by Various Externally Bonded Tension Reinforcements

Optimized Design of Anchor Plates for 2200 MPa-Class Prestressing Anchorage Zones

Experimental Evaluation of Strut-and-Tie Model of Anchorage Zone in Posttensioned Concrete Structures

A design approach for the interior anchorage zone of post-tensioned concrete structure

Performance Assessment of the Post-Tensioned Anchorage Zone Using High-Strength Concrete Considering Confinement Effect

Nonlinear Analysis of External Post-Tensioning anchorage of Concrete Segment

Effects of Ordinary Tension Reinforcement on the Response of Beams with Unbonded Tendons

Investigation and Improvement of Strut-and-tie Model for Design of End Anchorage Zone in Post-Tensioned Concrete Structure

The Finite Element Analysis of the End Anchorage under Larger Prestressing Load in Rehabilitation Engineering

Stress Analysis on Steel Anchor Block of External Prestressing Concrete Bridges

Experimental and Numerical Study of Corrugated Anchors for CFRP Plates

Development of a Novel Anchorage and Tensioning System for Strengthening Steel Beams with Unbonded Prestressed CFRP Plates

Experiment Program on Retrofitted Anchorage System under Impact Loads

Anchoring and stressing methods for prestressed FRP plates: State-of-the-art review

NONLINEAR FINITE ELEMENT ANALYSIS OF MECHANICALLY ANCHORED REINFORCED STEEL I BEAMS

Computer Simulations of End-Tapering Anchorages of EBR FRP-Strengthened Prestressed Concrete Slabs at Service Conditions

Full-Scale Segment Model Test and Performance Improvement Scheme of Cable-Pylon Anchorage Zone for Cable-Stayed Bridge

Stressing State Analysis of Partially Prestressed Concrete Beams with High Strength Reinforcement Based on NSF Method.

Tensile Performance of Headed Anchors in Steel Fiber Reinforced and Conventional Concrete in Uncracked and Cracked State

Study on Eccentrically-compressed Performance and Influencing Factors of Prestressed Steel Reinforced Members