Abstract:Advanced Li-ion batteries adopting new cathode chemistries are required for the successful widespread transition to electric vehicles (EVs) and renewable energy sources, aiming for high energy density, long cycle life, and good rate capability. Commercial candidates for EV batteries include Ni-rich Li(Ni x Mn y Co 1−x-y )O 2 (NMC) cathodes, with Ni:Mn:Co ratios of 8:1:1 (NMC811) and higher. These are favored because of their high specific capacity (~ 200 mAh g -1 )and reduced cobalt content. Despite all of the advantages, these materials suffer from a range of degradation modes, many of which are associated with the redox and crystallographic behavior at high states of charge. In particular, Ni-rich cathodes suffer from several limitations, such as rapid capacity fade in comparison to NMC stoichiometries with lower Ni content. In addition, they also have a lower onset voltage for oxygen release and subsequent surface reconstruction leading to the formation of spinel and rock salt phases which impede (de)lithiation and therefore the achievable capacity of the cell. 1 Crystallographic properties of electrode materials are intrinsically linked to the electrochemical performance of the cell. NMC materials suffer from anisotropic changes in the crystal structure during cycling which induces strain and leads to issues such as crack formation, expediting degradation. One method to tackle capacity fade is to switch to single-crystal morphologies (particle size 1-3 μm) which have better mechanical stability than conventional polycrystalline morphologies (secondary agglomerate particles ~ 10 μm made up of primary particles which are 100 nm – 1 μm in size) and have less propensity to form extensive rock-salt layers. It is thought that the single-crystal morphology helps to reduce stress in the material as the anisotropic stress in polycrystalline cathodes is concentrated at grain boundaries. However, there is still a limited understanding of the subtle mechanistic differences between the two materials during cycling. 2 A multi-scale approach is required to gain a more comprehensive understanding of the degradation mechanisms at play and how they initiate and propagate. In this work, synchrotron diffraction methods were employed at the crystal, particle and cell scale using a variety of techniques including in-situ Bragg Coherent Diffraction Imaging (BCDI), 3D-XRD and operando high-resolution XRD. Intra-particle, inter-particle and electrode level heterogeneities were observed during cycling, both in pristine and aged samples. It is believed that these heterogeneities accelerate the loss of performance at the cell level by inducing crack formation which can then be observed in X-ray computed tomography data acquired in simultaneous lab studies. The overarching goal of these investigations is to add to the understanding of complex degradation mechanisms for Ni-rich layered transition metal oxide cathodes, ultimately aiding in the informed development of future battery electrode materials. References: 1] Xu, C. et al., Phase Behaviour during Electrochemical Cycling of Ni‐Rich Cathode Materials for Li‐Ion Batteries. Adv. Energy Mater. 2021, 11, 2003404. 2] Yin, S. et al., Fundamental and solutions of microcracks in Ni-rich layered oxide cathode materials of lithium-ion batteries. Nano Energy, 2021, 83, 105854.

The capacity fading mechanism of high-capacity CrOx (x ≥ 2.5) cathode material for lithium-ion battery

Electrochemical Performance of CrOx Cathode Material for High Energy Density Lithium Batteries

Synthesis and Reversible Lithium Storage of Cr2o5 As A New High Energy Density Cathode Material for Rechargeable Lithium Batteries

Electrochemical Behaviours and Structure Evolution of High Capacity Li1.2Cr0.4Mn0.4O2 Cathode Material in a Wide Voltage Range

Rate-dependent Electrochemical Reaction Mechanism of Spinel Metal Oxide Anode Studied by in Situ TEM

Probing Reversible Multielectron Transfer and Structure Evolution of Li1.2Cr0.4Mn0.4O2 Cathode Material for Li-Ion Batteries in a Voltage Range of 1.0–4.8 V

The effect of chromium substitution on improving electrochemical performance of low-cost Fe-Mn based Li-rich layered oxide as cathode material for lithium-ion batteries

Layered-to-Rock-Salt Transformation in Desodiated NaCrO2

Electrochemically Driven Phase Transition in LiCoO2 Cathode

Improving electrochemical performances of Lithium-rich oxide by cooperatively doping Cr and coating Li<sub>3</sub>PO<sub>4</sub> as cathode material for Lithium-ion batteries

Impact of Cr Doping on the Voltage Fade of Li-Rich Mn-Rich Li 1.11 Ni 0.33 Mn 0.56 O 2 and Li 1.2 Ni 0.2 Mn 0.6 O 2 Positive Electrode Materials

Reversibility of Ni-Rich Layered Cathode Material Revealed by Structural, Spectroscopic and Imaging Characterizations

Mechanochemically Robust LiCoO2 with Ultrahigh Capacity and Prolonged Cyclability

Communication—Cubic Lithium Chromium Oxide (lixcr2o5) As a New Cathode Material for Lithium Ion Batteries

Polyhedral perspectives on the capacity limit of cathode compounds for lithium-ion batteries: a case study for Li6CoO4

A New Insight into the Capacity Decay Mechanism of Ni‐Rich Layered Oxide Cathode for Lithium‐Ion Batteries

Improving electrochemical performances of Lithium-rich oxide by cooperatively doping Cr and coating Li3PO4 as cathode material for Lithium-ion batteries

Coordinate regulation of amorphous carbon microspheres and crystal structure of iron oxalate for high rate lithium storage ability

Suppressing the chromium disproportionation reaction in O3-type layered cathode materials for high capacity sodium-ion batteries

Insight into the capacity decay mechanism of cycled LiNi 0.5 Co 0.2 Mn 0.3 O 2 cathodes via in situ x-ray diffraction

Understanding the Degradation Mechanisms of Lithium Ion Batteries Using in-Situ Multi-Scale Diffraction Techniques