Abstract:Photocurable polymer provides fast curable properties via ultraviolet (UV) light for 3D‐printed propellants. This work outlines the preparation and characterization of photocurable fluorinated polyether‐based reactive inks. Acrylate‐terminated poly‐2‐((2,2,3,3,3‐pentafluoropropoxy)‐methyl) ethylene oxide (P5F‐AA) was synthesized as photocurable binder through the esterification of acrylic acid, and the terminal hydroxyl group of poly‐2‐((2,2,3,3,3‐pentafluoropropoxy)‐methyl) ethylene oxide (P5F), which was synthesized through cationic ring‐opening polymerization of 2‐((2,2,3,3,3‐pentafluoropropoxy)methyl) oxy‐ethane (PFEE) by using butane diol as initiator. In comparison with P5F, P5F‐AA had a lower glass transition temperature (Tg) of −63.3°C. A new type of photocurable resin, which may be used for additive manufacturing of energetic materials, was prepared via UV radiation in an LED UV curing tank by using P5F‐AA as prepolymer, diphenyl (2,4,6‐trimethyl benzoyl) phosphine oxide (TPO) as photo‐initiator, and tri‐fluoroethyl acrylate (3F‐AA) and 1,6‐hexanediol diacrylate (HDDA) as mono‐ and multifunctional diluents, respectively. When the mass ratio of P5F‐AA/3F‐AA/HDDA binder matrix was 1:1:0.5, the sample exhibited maximal mechanical strength of 6.56 MPa with elongation at break of 13.38%, which was due to the introduction of HDDA effectively increasing the "entanglement" between molecular chains. Thermogravimetric analysis (TGA‐DTG) was utilized to evaluate the ability to decompose thermally of the binder matrix, and the results showed the initial degradation temperature started at nearly 181°C and two consecutive stages in thermal decomposition. Overall, the obtained results from the different techniques suggested that P5F‐AA/3F‐AA/HDDA binder matrix may be a photocurable reactive ink for 3D‐printed propellants, which would provide a certain reference value and guiding importance for design of reactive inks.

Preparation and characterization of complex shaped polytetrafluoroethylene (PTFE) parts based on vat photopolymerization 3D printing

Printing Depth Modeling, Printing Process Quantification and Quick-Decision of Printing Parameters in Micro-Vat Polymerization

Desktop printing of 3D thermoplastic polyurethane parts with enhanced mechanical performance using filaments with varying stiffness

Preparation of PVDF/PVA composite films with micropatterned structures on light-cured 3D printed molds for hydrophilic modification of PVDF

Effect of 3D Printing Process Parameters and Heat Treatment Conditions on the Mechanical Properties and Microstructure of PEEK Parts

Influence of thermal processing conditions in 3D printing on the crystallinity and mechanical properties of PEEK material

Design and Depolymerization of Bis(2‐hydroxyethyl) Terephthalate‐Containing Polyurethanes for Vat Photopolymerization

3D printing of ultra-high viscosity resin by a linear scan-based vat photopolymerization system

A Comprehensive Investigation on 3D Printing of Polyamide 11 and Thermoplastic Polyurethane via Multi Jet Fusion

Research on the Fused Deposition Modeling of Polyether Ether Ketone

Effect of Thermal Processing and Heat Treatment Condition on 3D Printing PPS Properties

Achieving high geometric fidelity in vat photopolymerization additive manufacturing through liquid surface support

A Novel Route to Fabricate High-Performance 3D Printed Continuous Fiber-Reinforced Thermosetting Polymer Composites

Tensile and Bending Strength Improvements in PEEK Parts Using Fused Deposition Modelling 3D Printing Considering Multi-Factor Coupling

Preparation and characterization of photocurable fluorinated polyether‐based reactive inks

Structure-Processing-Property Relationships of 3D Printed Porous Polymeric Materials

High-performance PZT Piezoelectric Ceramic Materials for Photocuring 3D Printing

Effect of process parameters on properties of 3D printed continuous fiber reinforced thermoplastic composites

Slowing crystallization to enhance interlayer strength of 3D printed poly (ether ether ketone) parts by molecular design

Feasibility Study on the Fused Filaments of Injection-Molding-Grade Poly(Ethylene Terephthalate) for 3D Printing

On the 3D printing of polypropylene and post-processing optimization of thermomechanical properties