Abstract:Piezoelectric composites made of piezoelectric ceramic particles and polymer composites combine the performance advantages of both components and have broad application prospects. However, the preparation of complex structures is still a challenge, for which 3D printing technology provides a perfect solution. The aim of the present study is to investigate the principle and process optimization of the stereolithography of 0–3 type piezoelectric composites through simulation and experiments. In particular, a modified three-phase model of a spherical shell is applied to elucidate the influence of the elastic modulus between the ceramic particles and the matrix on the piezoelectric properties of the composites at the macroscopic level. This enables the piezoelectric properties of the composites to be predicted more accurately, and guides the surface grafting modification of piezoelectric ceramic powders. Furthermore, the problem of weak interface bonding in piezoelectric composites caused by poor compatibility between hydrophilic particles and the hydrophobic matrix is successfully solved by preprocessing the PZT ceramic powder via activating the particle surface hydroxyl groups and grafting a silane coupling agent onto the piezoelectric ceramic powder. As a result, the particles are bonded to the matrix by covalent bonds, which increases the elastic modulus of the interface transition layer and modifies the stress transfer efficiency. For instance, the piezoelectric strain constant ( d 33 ) of piezoelectric composite containing 60 wt% functionalized PZT particles is increased from 20 to 37 pC/N. The printing accuracy, piezoelectric properties, and mechanical characteristics of the piezoelectric composites are thoroughly investigated, and the reliability of the proposed theoretical model and simulation results is verified. The piezoelectric composites are uniformly compact and have a low residual pore rate. The piezoelectric composite with a solid content of 60 wt% has a volume density of 2.27 g/cm3 and a Young's modulus of 535.44 MPa. Most importantly, its piezoelectric voltage constant ( g 33 ) is 167.2 × 10−3 Vm/N, which is more than seven times higher than that of homogeneous PZT and results in high voltage sensitivity.

High-performance PZT Piezoelectric Ceramic Materials for Photocuring 3D Printing

Effect of the slurry composition on the piezoelectric properties of PZT ceramics fabricated via materials extrusion 3D printing

Piezoelectric-pneumatic micro-jet printing of high viscous piezoelectric slurry

Photopolymerization-Based Three-Dimensional Ceramic Printing Technology

3D printing of lead zirconate titanate piezoelectric ceramics via digital light processing (DLP)

Fabrication of porous PZT ceramics using micro-stereolithography technology

Direct ink writing of 3D piezoelectric ceramics with complex unsupported structures

Parameter Optimization for Printing Barium Titanate Piezoelectric Ceramics through Digital Light Processing

Preparation of high solid loading and low viscosity ceramic slurries for photopolymerization-based 3D printing

Mechanical and Dielectric Properties of 3D Printed Highly Porous Ceramics Fabricated Via Stable and Durable Gel Ink

3D printed 0–3 type piezoelectric composites with high voltage sensitivity

Hydrogel-based DLP 3D Printing of Dense Zirconia Ceramics

Optimizing photocuring properties of ceramic slurry for 3D printing of ceramic membranes

Three-Dimensional Printing of Ceramics through "Carving" a Gel and "Filling in" the Precursor Polymer

Study on the control of mechanical and electrical properties of 3d printed BTO/PDMS flexible porous composites

Properties and ceramic transformation of Si–Zr–O–C precursor ceramics with porous structure

Defect inhibition mechanism of 3D‐printed ceramics via synergetic resin composition and debinding processing regulation

Preparation and stereolithography 3D printing of ultralight and ultrastrong ZrOC porous ceramics

Preparation of excellent performance ZTA ceramics and complex shaped components using digital light processing 3D printing technology

Relationship of Electrical Properties and Partical Size of Piezoelectric Ceramics Fabricated by Digital Light Processing 3D Printing

Photopolymerization of ceramic/zeolite reinforced photopolymers: Towards 3D/4D printing and gas adsorption applications