Abstract:The morphological evolution and grain orientations of intermetallic compounds (IMCs) were investigated during the formation of full Cu3Sn joints at two soldering temperatures (310 and 430 °C). The mechanical properties of both types of full Cu3Sn joints were then analyzed. The experimental results showed that the morphology of interfacial IMCs varied significantly at two temperatures. At 310 °C, scallop-like Cu6Sn5 grains became larger but were fewer in number and the top of the scallops became rough due to the grain ripening effect. With the increase in the soldering temperature to 430 °C, Cu3Sn no longer grew uniformly as observed during soldering at 310 °C, but exhibited various growth rates. Furthermore, some η-Cu6Sn5 transformed into η′-Cu6Sn5 during cooling, and the following orientation groups between η′-Cu6Sn5 and η-Cu6Sn5, i.e., {102}η′ and {<math>112‾0</math>}η, {112}η′ and {<math>101‾0</math>}η, and {<math>2‾01</math>}η′ and {0001}η, were found to be near-parallel. The Cu3Sn grains were preferably oriented with [203] and [100] crystal orientations parallel to transverse direction (TD) at both temperatures. Noteworthy, the Cu3Sn grains with [203]//TD and [010]//ND grew much faster than those with other orientations at 430 °C. Moreover, molecular dynamics simulation showed that the diffusion coefficients of atoms in Cu3Sn crystals along [203] direction were significantly greater than those in other low-index crystal directions. After soldering, two types of full Cu3Sn joints obtained at different temperatures exhibited different shear strength and fracture mechanisms.

Formation and evolution of irregularly arranged prism-type Cu6Sn5 grains on electroplated (111) textured Cu

Orientation transformation of Cu6Sn5 grains by Ag addition in Cu/Sn-xAg/Cu micro solder joints under temperature gradient

Thermal and Compositional Fields to Maneuver Cu 6 Sn 5 Intermetallic Growth on (111) Nanotwinned Copper Substrate

Morphology evolution and grain orientations of intermetallic compounds during the formation of full Cu3Sn joint

Abnormal Grain Growth in Cu6Sn5 Grains Formed at SN-based Solder/cu Interfaces

Influence behavior and mechanism of crystal orientation of Cu 6 Sn 5 coating on interfacial intermetallic compounds growth in Sn-0.7Cu/Cu solder joint

Stepped Interface and Crystal Orientation in the Eutectic Structure of Cu-71.8%Ag Alloy

Investigation on growth of the orientation-preferred Cu6Sn5 on (001)Cu during the temperature-increased multiple reflow process

Heredity of preferred orientation of β-Sn grains in Cu/SAC305/Cu micro solder joints

Morphologies and grain orientations of CuSn intermetallic compounds in Sn3.0Ag0.5Cu/Cu solder joints

Repeated 3D Nucleation in Electroless Cu Deposition and the Grain Boundary Structure Involved

The Effect of Cu Orientation on Fracture Location in Cu<inf>3</inf>Sn-Cu Interface Structure Under Monotonic Loading Condition by Molecular Dynamics Simulation

Growth behavior and morphology evolution of interfacial (Cu,Ni)6Sn5 in (001)Cu/Sn/Ni micro solder joints

Nucleation and growth of Cu6Sn5 during the aging process of Cu/Sn interface in electronic packaging-by in-situ TEM

High-temperature effects on kinetics and grain orientation of the Cu41Sn11 phase formed from the full Cu3Sn joint during the aging process

Inclined θ′ precipitates with terraced Cu/Mn-rich multilayers in Al–Cu alloys

Enhancement of Abnormal Grain Growth by Surface Quenching Treatment to Eliminate Cu–Cu Bonding Interfaces Using (111)-Oriented Nanotwinned Copper

In-situ electron backscatter diffraction of thermal cycling in a single grain Cu/Sn-3Ag-0.5Cu/Cu solder joint

Evolution of Cation Ordering and Crystal Defects Controlled by Zn Substitutions in Cu2SnS3 Ceramics

Effect of impurities on anisotropic grain growth in (111)-oriented nanotwinned copper

Study on the evolution of interfacial (Cu,Ni)6Sn5 and shear property of (111)Cu/Sn/Ni micro joints under isothermal and TG-bonding