Abstract:Amorphous SiBCN ceramics are a unique class of structure materials with potential applicationsas high-temperature heat-resistant structural components owing to their combination of special structure and properties of low specific weight, high specific strength and excellent damage tolerance at elevated temperatures. However, it is still in need for further mechanical properties improvements for actual demands by rational co-design of architecture and chemistry as well as understanding the basic features of morphological/microstructural evolution and failure behavior. Thus in this attempt, to target the dense amorphous Si2ByC2N (y=1.5～4) monoliths with high mechanical properties, an attractive way of combinatorial mechanical alloying and high-pressure sintering technique (1000 oC/3～5 GPa/30 min) was proposed using elemental powders of graphite, hexagonal BN, cubic Si and boron as raw materials. The sintering pressure induced microstructural evolution, phase transformation and thermal stability have been investigated by XRD, SEM, TEM and TG measurements, and mechanical performance, especially the fracture behavior was also discussed in details. Results clearly presented that an increase in sintering pressure promoted the phase transformation of completely amorphous matrix to a hybrid structure of substantial amorphous phases and few nanocrystals of metal c-Si and/or t-BN(C) for some monoliths, implying boron-content depending phase composition. High-pressure sintering effectively promoted the densification leading to free volume annihilation and the river-like fracture morphology occurrence. A monotonous increase of the bulk density, nano hardness and Young's modulus as a function of the sintering pressure was observed. Under the same sintering conditions, the increase in boron content weakened the mechanical properties and thermal stability of the amorphous Si2ByC2N (y=1.5～4) monoliths. Dense amorphous Si2B1.5C2N monoliths consolidated at 1000 oC/5 GPa/30 min showed the best performance with the bulk density, nano hardness and Young's modulus obtaining at 2.69 g/cm3, 33.6±2.2 GPa and 414.2±16.5 GPa, respectively.

Synthesis and investigation of structural properties of high-quality niobium disilicon ceramics at high pressure and high temperature

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Production of silicon carbide reinforced molybdenum disilicide composites using high-pressure sintering

Multifunctional tantalum disilicide ceramics sintered at high temperature and high pressure

High-pressure Synthesis, Mechanical Properties and Oxidation Behavior of Advanced Boron-Containing Α/β-Si 3N 4/si Ceramics Using Polymer-Derived Amorphous SiBN Ceramics

Microstructural evolution and mechanical performance of high-pressure sintered dense amorphous SiBCN monoliths

Investigation of the microstructure and physical properties of TaSi 2 sintered at high temperature and high pressure

Low temperature sintering of Hf0.95Nb0.05B2-based ceramics with submicron-scaled grains and enhanced mechanical properties

Pressureless Sintering and Properties Investigation of Silicon Nitride

Advanced Fabrication Method and Mechanical Properties of Silicon Nitride/Boron Nitride Fibrous Monolithic Ceramics

Microstructure and high-temperature properties of SI-B-C-N MA-powders and ceramic

Synthesis and Characterization of Superconducting NbC Nanotubes

The microstructural evolution, mechanical and dielectric properties of BNW/SiO2 ceramics

Phase evolution and oxidation resistance of Si3N4/HfB2/HfB C N1–– ceramic nanocomposites prepared from tailored preceramic polymers

Fabrication of high thermal conductivity silicon nitride ceramics by pressureless sintering with MgO and Y2O3 as sintering additives

Pressureless Sintering and High-Temperature Strength of SiC-AlN Ceramics

Synthesis and Consolidation of Composite Materials in the SiC–Si3N4–Si2N2O System

Processing and Characterization of SiB0.5C1.5N0.5 Produced by Mechanical Alloying and Subsequent Spark Plasma Sintering

The effect of pressure tuning on the structure and mechanical properties of high-entropy carbides

Low temperature fabrication of highly dense α‐Si3N4 ceramics

Densi Cation and Crystallisation Behaviour of Si–B–O–N Ceramics Prepared by Hot Pressing with Organic Precursors