Abstract:In order to reduce the distortion caused by welding of rail vehicles made of chromium‐nickel steel, an in situ alloying process for a low transformation temperature (LTT) effect was developed from commercially available materials. Demonstrators with and without low transformation temperature effect were welded in an automated robotic welding process and the distortion was measured. The low transformation temperature effect reduced the distortion by up to 78 %. Due to their low thermal conductivity and high thermal expansion, austenitic chromium‐nickel steels have an increased tendency to distortion during welding. In industrial sectors such as rail vehicle construction, there is a high demand for geometrical precision that is not met by distorted components. Introducing a low transformation temperature (LTT) effect in the weld seam influences the stress distribution, which effects the formation of welding distortion. The low transformation temperature effect is achieved by in situ alloying using commercially available materials. The demonstrators made of stainless steel (X2CrNiN18‐7/1.4318) were welded with a low‐alloy filler metal G4Si1. The low transformation temperature effect is assessed by energy dispersive x‐ray spectroscopy and hardness measurements. The effect on distortion was investigated by measuring the demonstrators with a coordinate measuring system and the results were compared with the reference stainless steel demonstrators with stainless filler metal. The alloying process resulted in a reduction of the alloy content to 14.4 m% chromium and 5 m% nickel and a medium‐high hardness of 361 HV 0.2 to 383 HV 0.2. The low transformation temperature effect achieved leads to a significant reduction in welding distortion of up to 78 % compared to the similar reference demonstrators. Translation abstract Austenitische Chrom‐Nickel Stähle neigen aufgrund ihrer geringen Wärmeleitfähigkeit und hohen Wärmeausdehnung verstärkt zum Verzug beim Schweißen. In Industriezweigen wie dem Schienenfahrzeugbau werden hohe Anforderungen an die geometrische Präzision gestellt, die durch verzogene Bauteile nicht erfüllt werden. Das Einbringen eines Niedrigtransformationstemperatureffektes (LTT) in die Schweißnaht beeinflusst die Spannungsverteilung, was sich auf die Entstehung von Schweißverzug auswirkt. Der Niedrigtransformationstemperatureffektes wird durch in situ Legieren mit handelsüblichen Werkstoffen erreicht. Die Demonstratoren aus nichtrostendem Stahl (X2CrNiN18‐7/1.4318) wurden mit einem niedriglegierten Schweißzusatzwerkstoff G4Si1 verschweißt. Der Niedrigtransformationstemperatureffektes wird durch energiedispersive Röntgenspektroskopie und Härtemessungen beurteilt. Der Einfluss auf den Verzug wurde durch Vermessung der Demonstratoren mit einem Koordinatenmesssystem untersucht und die Ergebnisse mit den Referenzdemonstratoren aus nichtrostendem Stahl geschweißt mit nichtrostendem Schweißzusatz verglichen. Durch den Legierungsprozess wurde eine Reduzierung des Legierungsgehalt auf 14.4 m% Chrom und 5 m% Nickel und eine mittelhohe Härte von 361 HV 0.1 bis 383 HV 0.1 erreicht. Der erzielte Niedrigtransformationstemperatureffektes führt zu einer signifikanten Reduzierung des Schweißverzugs von bis zu 78 % im Vergleich zu den artgleichen Referenzdemonstratoren.

Adjustment of chemical composition with dissimilar filler wire in 1.4301 austenitic stainless steel to influence residual stress in laser beam welds

Capability of martensitic low transformation temperature welding consumables for increasing the fatigue strength of high strength steel joints

Effect of Tensile Deformation on Microstructure and Corrosion Resistance of High Nitrogen Austenitic Stainless Steels

Reduction of friction stir welding setup loadability, process forces and weld seam width by tool scaling

Metallurgical investigation of electron beam welded duplex stainless steel X2CrNiMoN22-5-3 with plasma nitrided weld edge surfaces

Influence of degree of deformation on welding pore reduction in high-carbon steels

Reduced spheroidization in rail flash-butt welding by selective alloying

Microstructural and mechanical characterization of electron beam welded low-nickel nitrogen-strengthened austenitic stainless steel

Trag‐ und Ermüdungsverhalten von Stumpfnähten in Blechen unterschiedlicher Dicken

Corrosion behavior of austenitic stainless steel and nickel-based welded joints in underwater wet welding

Low-Temperature Plasma Nitriding of Martensitic and Austenitic Steels to Increase Tribocorrosion Resistance*

Consequences of thermite welding on the microstructure of the heat affected zone of a carbide-free bainitic steel rail

Investigations on metallurgical and mechanical properties of resistant spot welded dissimilar joints between a high manganese steel and a low alloyed steel grade

Heat-affected zone ferrite content control of a duplex stainless steel grade to enhance weldability

Cold Metal Transfer Welding of Ferritic and Austenitic Stainless Steel: Microstructural, Mechanical, and Electrochemical Studies

Reparaturschweißen an Brücken im Betrieb

Untersuchungen zur Schubtragfähigkeit von Blechen aus nichtrostendem Stahl

Microstructural Evolution, Ferrite Content, and Grain Size Study in the Coalescence of High Nitrogen Austenitic Stainless Steel Thick Plates Using Cold Metal Transfer Welding Process

Quenching Distortion of Aluminium Castings – Improvement by Gas Cooling

Process-adapted temperature application within a two-stage rivet forming process for high nitrogen steel