Abstract:In this study, the effects of Si content on the glass-forming ability (GFA), thermal stability, annealing window, nanocrystallization process, and soft magnetic properties (SMPs) of Fe 86.3-x Si x B 10 P 2 Cu 1.7 (x = 0, 1, 2, 3, and 4, denoted as Si0, Si1, Si2, Si3, and Si4, respectively) alloys with high Fe and Cu contents were investigated. Moderate addition of Si (x = 1, 2, and 3) enhanced the GFA and suppressed the precipitation of compound phases, thus leading to a large crystallization temperature interval ( ΔT x ) exceeding 185 °C for the alloys. Appropriate addition of Si also resulted in the formation of high-density and fine pre-existing α-Fe nanocrystals in as-spun ribbons and a high growth active energy of α-Fe crystals during the subsequent nanocrystallization process for the Si1, Si2, and Si3 alloys, enhancing competitive growth between α-Fe crystals and resulting in fine nanostructure and excellent SMPs of the nanocrystalline alloys (NAs). As a result, the Si1, Si2, and Si3 NAs obtained by annealing at 420 °C for 30 min exhibited excellent SMPs with saturation magnetic flux density ( B s ) up to 1.84 T and a low coercivity ( H c ) of approximately 10 A/m. In addition, statistical analysis of the relationship between the average grain size ( D ) of α-Fe crystals and H c values of the NAs indicated that an H c α D 3 dependence is observed when the D is less than approximately 30 nm, while this dependence follows the well-known H c α D 6 relationship when the D is above 30 nm. The dependency relationship between D and H c of NAs can guide the selection of an appropriate annealing process to optimize their SMPs.

The evolution of Σ3 grain boundaries in the strip-cast Hi-B grain orientated Fe-6.5% Si alloy

Effect of Σ3 grain boundaries on microstructure and properties of oriented Fe-6.5 wt%Si in twin-roll strip casting

Evolution from Amorphous to Nanocrystalline and Corresponding Magnetic Properties of Fe-Si-B-Cu-Nb Alloys by Melt Spinning and Spark Plasma Sintering

Goss Texture Evolution in a Grain-Oriented Fe-6.5wt%Si Steel Processed by Strip-Casting

Effects of boron content on the structure and magnetic properties of Fe81-xSi13BxMo2Cr1Cu1P2 nanocrystalline alloys

Effect of Si/B ratio on glass-forming ability, phase transitions and magnetic properties in (Fe40Ni40SixByCu1)0.97Nb0.03 alloys

Grain refinement mechanism of soft-magnetic alloys with nanocrystals embedded in amorphous matrix

Design of Fe-based nanocrystalline alloys with superior magnetization and manufacturability

The influence of cooling rate on microstructure and magnetic properties of cast Fe-6.5wt%Si steel

Crystallization behavior, soft magnetic properties and good bending ductility of high Fe content FeSiBCuPC alloys induced by composition design

A quasi-in-situ EBSD study on the formation and development of η-fiber in 0.15 mm ultra-thin Fe-4.5 wt. % Si sheet

Effects of Si addition on crystallization process and soft magnetic properties of high-Fe and high-Cu-content Fe-Si-B-P-Cu nanocrystalline alloys

Experimental Study on the Twin Roll Strip Casting and Warm Rolling Fe-6.5 Wt. %si Steel Sheet

The evolution of microstructure and magnetic properties of Fe–Si–Al powders prepared through melt-spinning

The effect of composition on glass-forming ability, crystallization behavior, and soft magnetic properties of FeSiBCuNbNiCo amorphous/nanocrystalline alloys

Grain boundary effect on the microstructure of solution-treated Fe-rich Sm-Co-Fe-Cu-Zr alloys

Effect of the substitution of Si for B on thermal stability, magnetic properties and corrosion resistance in novel Fe-rich amorphous soft magnetic alloy

Role of Inclusion, Microstructure and Texture Evolution in Soft Magnetic Properties of Fe–6.9 wt%Si Alloy with Yttrium Doping

Origin of the improved Bs for Fe-Si-B-Mn microalloyed amorphous alloys

Texture transition of shear bands in initially Goss–oriented grains in Fe–3 wt%Si alloy

Characterization of microstructure, texture and magnetic properties in twin-roll casting high silicon non-oriented electrical steel