Abstract:The methanation process, or Sabatier process, allows carbon dioxide and carbon monoxide to be hydrogenated into methane, which can be subsequently injected (once the gas grid specifications have been respected) into the gas network infrastructures already present in Europe. This process can be effectively adopted to convert captured CO 2 streams from power plants or hard to abate plants by using green hydrogen from renewable-driven water electrolysis. The technical aspects of concern in the methanation process are certainly the strong exothermicity of the process, with consequent possible generation of hotspots along the entire catalyst bed and the management of reaction heat through thermal recovery. These peculiar aspects influence the choice of construction materials and geometry of the methanation reactor, operating parameters, cooling system, type of catalyst/support and the initial conditions of the feed. In particular, the generation of hotspots influences the local kinetic reaction in the methanation reactor, the diffusional limits of hydrogen and carbon dioxide inside the catalyst and the chemical-physical characteristics of the catalyst bed. The present work reports a first scale-up of the Sabatier process, developed in Aspen Plus simulation environment, with the following characteristics: reactor size to process 925 Nm 3 /h, (750 hydrogen and 175 carbon dioxide), at 15 bar and 250 °C. After the implementation in the steady state, a dynamic simulation is performed to carry out a transient study of the entire plant. In particular, the attention is focused on the variation in the hydrogen load, produced by electrolysis from the energy surplus from renewable sources. Considering the variable nature of the power flow supplied to the electrolyser and therefore any shutdown and cold start-up phases of this equipment, the following load variation scenarios for the Power to Gas (PtG) system are simulated: −5%, +5% and −30 % molar flow rate of incoming hydrogen, compared to steady conditions used in the preliminary design of the equipment. The study highlights how the cooled reactor configuration is more performing and characterized by a lower number of reactors in series (2 reactors) when compared to the adiabatic configuration (5 reactors). Furthermore, in the cooled reactor configuration the control system is able to respond more quickly to load variations compared to that designed for the adiabatic case, although the latter is mostly adopted from the industrial viewpoint due to temperature control issues. Moreover, the control system manages to respond to load variations by bringing the values of interest (gas grid residual concentration of hydrogen and carbon dioxide, Wobbe index) into the target intervals.

Continuous and flexible Renewable-Power-to-Methane via liquid CO2 energy storage: Revisiting the techno-economic potential

Flexible and efficient renewable-power-to-methane concept enabled by liquid CO 2 energy storage: Optimization with power allocation and storage sizing

Dynamic-cycle Simulation of Power-to-methanol-to-power System with Reversible Solid Oxide Cells: Multi-physics and Techno-Economic Analysis

Power-to-Gas Energy Storage by Reversible Solid Oxide Cell for Distributed Renewable Power Systems

Synchronous Enhancement of H2O/CO2 Co-Electrolysis and Methanation for Efficient One-Step Power-to-methane

Geometric Synergy of Steam/Carbon Dioxide Co-electrolysis and Methanation in a Tubular Solid Oxide Electrolysis Cell for Direct Power-to-Methane

Site-dependent levelized cost assessment for fully renewable Power-to-Methane systems

A multi-step framework for the design of a flexible power-to-methane process

A Combined Investment and Operational Optimization Approach for Power-to-Methanol Plants

Production of Sustainable Methane from Renewable Energy and Captured Carbon Dioxide with the Use of Solid Oxide Electrolyzer: A Thermodynamic Assessment

Development of Highly Efficient Methanol Steam Reforming System for Hydrogen Production and Supply for a Low Temperature Proton Exchange Membrane Fuel Cell

Carbon Utilization Through Power to Gas and Oxyfuel Combustion Hybridization with Recycled CO2: Design and Preliminary Results

Study on the carbon migration from fossil fuel to liquid methanol by integrating solar energy into the advanced power system

Exergy Efficiency Analysis of a Power-to-Methane System Coupling Water Electrolysis and Sabatier Reaction

Power to Gas-Electrochemical Industry Hybrid Systems: A Case Study

Optimal Design and Off-Design Performance Improvement for Power-to-methane System Integrating Solid Oxide Electrolysis Cell with Methanation Reactor

Strategies for flexible operation of power-to-X processes coupled with renewables

Power-to-Gas: Process analysis and control strategies for dynamic catalytic methanation system

Integrated e-Methanol and Drop-in Fuels Hydrothermal Liquefaction Platform-Techno-Economic and GHG Emissions Assessment for Grid-Connected Plants under Flexible BECCU(S) Operation

Power-to-methanol: The role of process flexibility in the integration of variable renewable energy into chemical production

A System for the Combined Carbon Capture and Utilization to Produce Renewable Methanol from Biogas