Abstract:This article is focused on the experimental study of flexural properties in different multi-layer carbon fiber-reinforced polymer (CFRP) composites and correlations with the results of finite element method (FEM) simulations of mechanical properties. The comparison of the results shows the possibility of reducing the number of experimental specimens for testing. The experimental study of flexural properties for four types of carbon fiber-reinforced polymer matrix composites with twill weaves (2 × 2) was carried out. As input materials, pre-impregnated carbon laminate GG 204 T and GG 630 T (prepreg) and two types of carbon fiber fabrics (GG 285 T and GG 300 T (fabric)) were used. Multi-layer samples were manufactured from two types of prepregs and two types of fabrics, which were hand-impregnated during sample preparation. The layers were stacked using same orientation. All specimens for flexural test were cut with the longer side in the weft direction. Pre-impregnated carbon laminates were further impregnated with resin DT 121H. Carbon fabrics were hand-impregnated with epoxy matrix LG 120 and hardener HG 700. To fulfill the aim of this research, finite element method (FEM)-based simulations of mechanical properties were performed. The FEM simulations and analysis were conducted in Hexagon's MSC Marc Mentat 2022.3 and Digimat 2022.4 software. This paper presents the results of actual experimental bending tests and the results of simulations of bending tests for different composite materials (mentioned previously). We created material models for simulations based on two methods—MF (Mean Field) and FE (Finite Element), and the comparative results show better agreement with the MF model. The composites (GG 285 T and GG 300 T) showed better flexural results than composites made from pre-impregnated carbon laminates (GG 204 T and GG 630 T). The difference in results for the hand-impregnated laminates was about 15% higher than for prepregs, but this is still within an acceptable tolerance as per the reported literature. The highest percentage difference of 14.25% between the simulation and the real experiment was found for the software tool Digimat FE 2022.4 – GG 630 T composite. The lowest difference of 0.5% was found for the software tool Digimat MF 2022.4 – GG 204 T composite. By comparing the results of the software tools with the results of the experimental measurements, it was found that the Digimat MF 2022.4 tool is closer to the results of the experimental measurements than the Digimat FE 2022.4 tool.

Mechanical Properties and Economic Analysis of Fused Filament Fabrication Continuous Carbon Fiber Reinforced Composites

Experimental and Theoretical Studies on 3D Printed Short and Continuous Carbon Fiber Hybrid Reinforced Composites

Evaluation of the mechanical properties and performance cost of additively manufactured continuous glass and carbon fiber composites

Anisotropic mechanical properties of oriented carbon fiber filled polymer composites produced with fused filament fabrication

Fused-Deposition Modeling 3D Printing of Short-Cut Carbon-Fiber-Reinforced PA6 Composites for Strengthening, Toughening, and Light Weighting

Research into Specific Mechanical Properties of Composites Produced by 3D-Printing Additive Continuous-Fiber Fabrication Technology

Additive manufacturing of continuous fibre reinforced thermoplastic composites using fused deposition modelling: Effect of process parameters on mechanical properties

Mechanical properties of fiber reinforced polymer composites: A comparative study of conventional and additive manufacturing methods

Dimensional Accuracy and Mechanical Properties of Chopped Carbon Reinforced Polymers Produced by Material Extrusion Additive Manufacturing

Failure mode analysis and prediction model of additively manufactured continuous carbon fiber‐reinforced polylactic acid

Tensile fatigue behavior of short and continuous carbon fiber reinforced additively manufactured thermoplastic multiscale composite

Analysis of the Mechanical Characteristics and Properties of a Carbon Fiber–Nylon Composite Influence of the Factors of the Fused Deposition Modeling

Effect of infill density and reinforced perimeters on tensile properties and fracture mechanism of 3D printing carbon fiber–reinforced composite

Preparation and Evaluation of the Tensile Characteristics of Carbon Fiber Rod Reinforced 3D Printed Thermoplastic Composites

Thermal, Tensile and Fatigue Behaviors of the PA6, Short Carbon Fiber-Reinforced PA6, and Continuous Glass Fiber-Reinforced PA6 Materials in Fused Filament Fabrication (FFF)

Investigating the mechanical properties of 3D fused deposition modeling composites reinforced with continuous fibers: Effects of fiber number and negative Poisson structure

Comparison of Mechanical Property Simulations with Results of Limited Flexural Tests of Different Multi-Layer Carbon Fiber-Reinforced Polymer Composites

Assessment of the effects of the addition of continuous fiber filaments in PA 6/short fiber 3D-printed components using interrupted in-situ x-ray CT tensile testing

Fabrication and Formability of Continuous Carbon Fiber Reinforced Resin Matrix Composites Using Additive Manufacturing

Mechanical properties and damage failure of 3D‐printed continuous carbon fiber‐reinforced composite honeycomb sandwich structures with fiber‐interleaved core

Mechanical characteristics and failure morphology of FFF-printed poly lactic acid composites reinforced with carbon fibre, graphene and MWCNTs