Abstract:The best mechanical properties of 3D‐printed CF/PA6 were obtained by varying four printing parameters and using heat press processing. The inherent defects of the layer‐by‐layer manufacturing process limit the mechanical performance of 3D‐printed composite parts. This paper explores a process optimization method for continuous fiber composites 3D printing to improve the mechanical performance of 3D‐printed CF/PA6 (Carbon Fiber/Nylon 6) parts. First, the effects of printing temperature, printing speed, layer thickness, and side step on the mechanical performance of 3D‐printed CF/PA6 were studied by conducting variable parameter printing experiments. All optimal printing parameters for CF/PA6 were obtained, and their impact mechanisms were analyzed. Second, the coupling effect of temperature and pressure of post‐processing reduced the internal voids of 3D‐printed CF/PA6 and improved its mechanical properties. The influence mechanism of the coupling effect of temperature and pressure was summarized, and the optimal post‐processing parameters applicable to CF/PA6 were obtained. Based on the above process optimization, the fiber volume content of the printed CF/PA6 reached 41.05%, and the bending strength and elastic modulus reached 651.54 MPa and 79.08 GPa, which were 209.05% and 179.53% higher than those before optimization. Moreover, the tensile strength and elastic modulus reached 730 MPa and 29.23GPa, which were 98.10% and 81.10% higher than those before optimization. The experimental results give a positive validation of the effectiveness and feasibility of the proposed methodology. Highlights The effects of printing temperature, printing speed, layer thickness, and side step on the mechanical properties of 3D‐printed CF/PA6 were investigated. The optimal printing parameters applicable to CF/PA6 were obtained and their influence mechanisms were analyzed. The effects of the heat press processing method on the internal voids and mechanical properties of 3D‐printed CF/PA6 were investigated, and the optimal post‐processing parameters applicable to CF/PA6 were obtained. The study resulted in optimal printing parameters and post‐processing parameters for 3D printing CF/PA6, which greatly enhanced its tensile and flexural strength and modulus.

Crystallization and preliminary X-ray diffraction analysis of the di-haem cytochrome c peroxidase from Pseudomonas stutzeri.

Evolution of microstructure and thermo‐mechanical attributes of fiber reinforced polyamide during fused deposition modeling 3D printing: A comprehensive characterization study

Experimental and Theoretical Studies on 3D Printed Short and Continuous Carbon Fiber Hybrid Reinforced Composites

Additive manufacturing of high‐strength polyamide 6 composites reinforced with continuous carbon fiber prepreg

Performance enhancement of 3D‐printed carbon fiber‐reinforced nylon 6 composites

Evaluation of Carbon Fiber-Embedded 3D Printed Structures for Strengthening and Structural-Health Monitoring

Optimal short carbon fiber‐reinforced polyamide 6 composites with lifted high strength and toughness for fused filament fabrication

Preparation and Evaluation of the Tensile Characteristics of Carbon Fiber Rod Reinforced 3D Printed Thermoplastic Composites

Effects of FDM-3D printing parameters on mechanical properties and microstructure of CF/PEEK and GF/PEEK

Research into Specific Mechanical Properties of Composites Produced by 3D-Printing Additive Continuous-Fiber Fabrication Technology

CHARLES SEDGWICK MINOT, DECEMBER 23, 1852-NOVEMBER 19, 1914.

Properties of oriented carbon fiber/polyamide 12 composite parts fabricated by fused deposition modeling

Investigation on mechanical properties of polyamide 6 and carbon fiber reinforced composite manufactured by fused deposition modeling technique

3D Printing of Ultrahigh Strength Continuous Carbon Fiber Composites

Optimization of Production Parameters for Impact Strength of 3D-Printed Carbon/Glass Fiber-Reinforced Nylon Composite in Critical ZX Printing Orientation

Effects of infill density on mechanical properties of additively manufactured chopped carbon fiber reinforced PLA composites

Effect of infill density and reinforced perimeters on tensile properties and fracture mechanism of 3D printing carbon fiber–reinforced composite

ANALYSIS OF PRINTING PARAMETERS IN 3D PRINTED CARBON FIBER COMPOSITES USING DESIGN OF EXPERIMENTS

Investigation on the mechanical properties of 3D printed hybrid continuous fiber-filled composite considering influence of interfaces

High-Performance Polyamide/Carbon Fiber Composites for Fused Filament Fabrication: Mechanical and Functional Performances

Effect of process parameters of fused deposition modeling on mechanical properties of poly-ether-ether-ketone and carbon fiber/poly-ether-ether-ketone