Abstract:In order to improve the performance of proton exchange membrane（PEM） electrolyzer, reduce the voltage loss, and enhance the operational stability, a three-dimensional model of a full-size multi-channel PEM electrolyzer was established using Comsol software under certain assumptions. the simulation calculation results were compared with the experimental test results of the same size PEM electrolyzer in the literature to verify that the simulation results were basically consistent with the experimental test results in the literature. The effects of runner height, blocking and ridge width on the performance of PEM electrolyzer were investigated to optimize the flow field structure based on this electrolyzer model. The simulation results show that the optimal flow channel height is 2 mm under the PEM electrolyzer size set in the study. The oxygen mass fraction in the diffusion layer can be reduced by about 2.6%, the average temperature of the membrane electrode can be reduced by about 2.2 K, and the electrolytic potential of the electrolyzer can be reduced by about 0.023 5 V by setting the block at the top of the flow channel. When the width of the ridge of the flow field is reduced from 2 mm to 1 mm, the average oxygen mass fraction is decreased by about 8.7%, the average temperature of the membrane electrode is decreased by 6.21 K, and the electrolytic potential of the electrolyzer is decreased by about 0.04 V. The optimized flow field structure is conducive to take away oxygen in the diffusion layer for circulating water, and reduce the possibility of oxygen bubbles blocking the pores of the diffusion layer, reduce the mass transfer resistance, and enhance the heat transfer process to discharge the excess heat from the electrolyzer in time, reduce the electrolytic potential of the electrolyzer, and improve electrolyzer performance and operational stability.

Multi-objective optimization of channel structure for a proton exchange membrane water electrolysis cell

Modeling of Two-Phase Transport in Proton Exchange Membrane Electrolyzer Cells for Hydrogen Energy

Optimization of channel structure for proton exchange membrane fuel cells based on a three‐dimensional two‐phase flow model

Optimization of Flow Channel Design with Porous Medium Layers in a Proton Exchange Membrane Electrolyzer Cell

Channel/rib patterns optimization of a proton exchange membrane fuel cell by combining down-the-channel performance model and genetic algorithm

Simulation of the effect of flow channel structure on the performance of PEM electrolyzer

Design and Modelling of 3D Bionic Cathode Flow Field for Proton Exchange Membrane Fuel Cell

Three-dimensional Numerical Simulation of Bubble Dynamics and Design Optimization of Microchannel in Proton Exchange Membrane Water Electrolyzers

Effects of Membrane Electrode Assembly Properties on Two-Phase Transport and Performance in Proton Exchange Membrane Electrolyzer Cells

A Simulation Study on the Optimization of Flow Channel Pattern in High Temperature Proton Exchange Membrane Fuel Cell

Combination Effect of Flow Channel Configuration and Anode GDL porosity on Mass transfer and Performance for PEM Water Electrolyzer

Segmented Catalyst Layer with Varied Catalyst Loading to Improve the Cost Performance of Proton Exchange Membrane Electrolysis Cell, a Numerical Investigation

Microscale structure optimization of catalyst layer for comprehensive performance enhancement in proton exchange membrane fuel cell

Numerical Analysis of Air-Cooled Proton Exchange Membrane Fuel Cells with Various Cathode Flow Channels

Illustrative Case Study on the Performance and Optimization of Proton Exchange Membrane Fuel Cell

Multi-objective optimization of gradient gas diffusion layer structures for enhancing proton exchange membrane fuel cell performance based on response surface methodology and non-dominated sorting genetic algorithm-III

Optimization of Blocked Channel Design for a Proton Exchange Membrane Fuel Cell by Coupled Genetic Algorithm and Three-Dimensional CFD Modeling

Numerical Modeling and Topology Optimization for Designing the Anode Catalyst Layer in Proton Exchange Membrane Water Electrolyzers Considering Mass Transport Limitation

Modeling of a Novel Cathode Flow Field Design with Optimized Sub-Channels to Improve Drainage for Proton Exchange Membrane Fuel Cells

Enhancing heat dissipation and mass transfer of oxygen gas flow channel in a proton exchange membrane fuel cell using multiobjective topology optimization

Three-dimensional multiphase modeling of a proton exchange membrane electrolysis cell with a new interdigitated-jet hole flow field