Abstract:Numerous molecular dynamics (MD) simulations have been performed to investigate the effect of the nanopores on the martensitic transformation (MT) of pure iron (Fe) during the heating-cooling cycle. As per the simulation results, nanopores can obviously affect the difficulty on MT during the cooling process in two ways: On the one hand, the volume ratio of nanopores to simulation box model (R p/b ) can influence the distribution configuration of stacking fault (SF) to change the type of austenite microstructure during the heating process owing to the obstruction of the nanopores on the dislocation slip. The effect of nanopores is not obvious when R p/b is less than 2.22 %. The main type of austenitic changes from defect-free/simple-SF types to the intersecting-SF type and, finally, to the dislocation-cell type with an increase in R p/b from 2.22 % to 17.9 %. The dislocations in intersecting-SF type and dislocation-cell type austenitic microstructures can provide the nucleation site of MT, thus increasing the MT temperature. On the other hand, the high surface energy of the nanopores caused by the incomplete atomic lattice can provide the necessary energy for the nucleation of martensite, which then promotes the occurrence of MT during the cooling process. When the nanopores intersect with the dislocation wall in dislocation-cell type austenitic microstructure, martensite nucleates at the nanopores surface and then grows along the dislocation wall. In the previous investigation of selective laser melting martensitic steel, the nanopore in the microstructure was generally believed harmful to the mechanical property of specimen; however, in this study, it has been observed to promote the MT during solution-quenching heat treatment, which improves the mechanical property by improving the content of martensitic phase. This provides a new perspective in determining the significance of nanopores in microstructures.

Influence of pore defects on the mechanical property and corrosion behavior of SLM 18Ni300 maraging steel

Effect of Aging Temperature on Microstructure, Mechanical, and Wear Properties of 18Ni-300 Maraging Steel Produced by Powder Bed Fusion

Experimental Characterization and Strengthening Mechanism of Process-Structure-property of Selective Laser Melted 316 L

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Effect of heat treatment on the microstructure and mechanical properties of 2.4 GPa grade maraging steel fabricated by laser powder bed fusion

The Effect of Selective Laser Melting Fabrication Parameters on the Tensile Strength of an Aged New Maraging Steel Alloy with 8% Cr, Reduced Ni Content (7%), and No Co or Mo

Microstructure and Mechanical Properties of 18Ni-300 Maraging Steel Fabricated by Selective Laser Melting

Dependence of Microstructure, Relative Density and Hardness of 18Ni-300 Maraging Steel Fabricated by Selective Laser Melting on the Energy Density

Microstructural Evolution of a FeCo15Cr14Ni4Mo3 Maraging Steel with High Ductility Prepared by Selective Laser Melting

Effect of heat treatment on microstructure and mechanical properties of Fe–Cr–Ni–Co–Mo maraging stainless steel produced by selective laser melting

The Influence of Post-Treatment on Micropore Evolution and Mechanical Performance in AlSi10Mg Alloy Manufactured by Laser Powder Bed Fusion

A study on the microstructural evolution and subgrain size dependent constitutive equation of a type of maraging steel in the solid solution treatment process

Tuning process parameters to optimize microstructure and mechanical properties of novel maraging steel fabricated by selective laser melting

Formation and evolution mechanisms of pores in Inconel 718 during selective laser melting: Meso-scale modeling and experimental investigations

Dependence of microstructure and properties in additive manufactured 18Ni300 on heat treatment and surface enhancement

Influence of Aging Treatment Regimes on Microstructure and Mechanical Properties of Selective Laser Melted 17-4 PH Steel

Performance Study and Heat Treatment Analysis of Selective Laser Melting SiC/18Ni300 Martensitic Mold Steel Composites

The effect of nanopores on the mechanism of martensitic transformation in pure iron during the heating-cooling cycle: A molecular dynamics study

Microstructure Evolution, Mechanical Properties and Deformation Behavior of an Additively Manufactured Maraging Steel

Hot Deformation Behavior and Microstructure Evolution of the Maraging Stainless Steel

Mechanical Properties and Microstructure of Laser Powder Bed Fusion‐Processed 18Ni300 Maraging Steel According to Direct Aging Treatment Conditions