Abstract:The mechanical behavior of a commercially pure titanium (CP-Ti) is systematically investigated in quasi-static (Instron, servohydraulic) and dynamic (UCSD's recovery Hopkinson) compression. Strains over 40% are achieved in these tests over a temperature range of 77–1000K and strain rates of 10−3–8000/s. At the macroscopic level, the flow stress of CP-Ti, within the plastic deformation regime, is strongly dependent on the temperature and strain rate, and displays complex variations with strain, strain rate, and temperature. In particular, there is a three-stage deformation pattern at a temperature range from 296 to 800K, the specific range depending on the strain rate. In an effort to understand the underlying mechanisms, a number of interrupted tests involving temperature jumps are performed, and the resulting microstructures are characterized using an optical microscope. Based on the experimental results and simple estimates, it is concluded that the three-stage pattern of deformation at temperatures from 296 to 800K, is a result of dynamic strain aging, through the directional diffusion of dislocation-core point defects with the moving dislocation at high strain rates, although the usual dynamic strain aging by point defects segregating outside the dislocation core through volume diffusion is also observed at low strain rates and high temperatures. The microscopic analysis shows that there is substantial deformation twinning which cannot be neglected in modeling the plastic flow of CP-Ti. The density of twins increases markedly with increasing strain rate, strain, and decreasing temperature. Twin intersections occur, and become more pronounced at low temperatures or high strain rates. In sum, the true stress–true strain curves of CP-Ti show two stages of deformation pattern at low temperatures, three stages at temperatures above 296K, and only one stage at temperatures exceeding 800K, although all three stages may exist even at 1000K for very high strain rates, e.g. 8000/s. While the dislocation motion is still the main deformation mechanism for plastic flow, the experimental results suggest that dynamic strain aging should be taken into account, as well as the effect of deformation twinning.

Abnormal strain hardening in nanostructured titanium at high strain rates and large strains

Mechanical properties and deformation mechanisms of a commercially pure titanium

Anisotropic Plasticity of Nanocrystalline Ti:A Molecular Dynamics Simulation

Stable strain hardening behavior of Ti-4Al-5Mo-5V-5Cr-1Nb alloy during plastic deformation

Dynamic Deformation and Failure of Ultrafine-Grained Titanium

Evidence for a Transition in Deformation Mechanism in Nanocrystalline Pure Titanium Processed by High-Pressure Torsion

In-situ Investigation Via High Energy X-ray Diffraction of Stress-Induced(0002)α→(110)β Transformation in a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr Alloy

Characterization and Analysis of Strain Heterogeneity at Grain-Scale of Titanium Alloy with Tri-Modal Microstructure During Tensile Deformation

Effect of Strain Rate and Temperature on the Deformation Behavior in a Ti-23.1Nb-2.0Zr-1.0O Titanium Alloy

The Mechanical Response and Failure Mechanism of a Near Α Titanium Alloy under High-Strain-rate Compression at Different Temperatures

Adiabatic shear instability in a titanium alloy: Extreme deformation-induced phase transformation, nanotwinning, and grain refinement

Forced shear deformation behaviors of annealed pure titanium under quasi-static and dynamic loading

The Microstructures and Deformation Mechanism of Hetero-Structured Pure Ti under High Strain Rates

Strain rate-dependent hardness and deformation behavior in the nanocrystalline/amorphous Ti2AlNb film

From Strain Softening to Strain Hardening in Submicron Scale Ti2448 Associated with Slip Mode Transition Mediated by Nanoscale Martensitic Transformation

High strain rate mechanical behavior of Ti-6Al-4V with micro–macro correlation under compressive loading

In Situ Synchrotron X-ray Diffraction Investigations of the Physical Mechanism of Ultra-Low Strain Hardening in Ti-30Zr-10Nb Alloy

Mechanical Properties and Microstructure in a Fine Grained Ti-5Al-5Mo-5V-1Cr-1Fe Titanium Alloy Deformed at a High Strain Rate

Deformation Behavior and Plastic Instabilities of Ultrafine-Grained Titanium

Temperature and Strain Rate Effect of the Deformation-Induced Phase Transformation in Pure Titanium Nanopillars Oriented along [0 0 0 1]

Abnormal Work Hardening in a TRIP-assisted Metastable Β Titanium Alloy under High Strain Rate Loading