Abstract:BackgroundThe flexibility in designing the submucosal part of CAD/CAM customized implant abutments and the individual positioning of its shoulder line has been suggested to reduce the risk of leaving undetected cement residues, thus preventing adverse effects on peri-implant tissues. A high correlation between excess cement left in the soft tissues and the occurrence of increased biofilm accumulation with sulcular bleeding and/ or suppuration has been reported. This in turn may cause peri-implant inflammation and peri-implant marginal bone loss. The aim of this study was to assess the frequency of cement remnants after the luting of zirconia crowns on CAD/CAM custom molar abutments with different margin levels and to evaluate the impact of the luting material.Material and methodsA total of 20 titanium molar CAD/CAM implant abutments (BEGO Medical GmbH) with internal taper connection/ internal hex anti-rotation protection, and a convex emergence profile with different margin positions (0, 1, 2 and 3 mm below the mucosa), were virtually designed (Implant Studio, 3Shape) and manufactured. A master cast was scanned, duplicated by a 3D printer and individual gingival masks were produced to simulate peri-implant soft tissues. 20 corresponding zirconia crowns were designed (Cerec 3D, Dentsply Sirona), produced and cemented to the abutments with two different luting materials; a zinc oxide non-eugenol cement (Temp Bond NE) or a methacrylate cement (Panavia V5). To ensure retrievability of the crown/abutment connection, occlusal openings providing access to the abutment screws were designed. Excess cement was thoroughly removed and the crown/abutment units were unscrewed to evaluate the occurrence of cement residues. All the quadrants of each specimen were evaluated for calculation of the ratio between the cement remnant area and the total specimen area using Adobe Photoshop. Spearman analysis was performed to detect correlations between different variables. A two-sided t-test, ANOVA, Mann–Whitney, and Kruskal–Wallis tests were applied to detect differences between the groups.ResultsCement remnants were found in every depth of the crown abutment complex and in almost every area investigated. The amount of cement residues increased as the crown-abutment margin was located more submucosally. Lingual areas were more prone to cement remnants than other surface areas (p = 0.0291). Excess cement was not only found at the margins of the crown-abutment complex, but also underneath (basal) the abutment itself, where cleaning was impossible. No statistical difference in the effect of zinc oxide non-eugenol- and methacrylate cement on the frequency of excess material at the lateral abutment surfaces could be demonstrated in vitro. The proportion of basal abutment aspects covered with cement residues was, however, significantly smaller in Panavia V5 samples with an average of 4.9 ± 3.7% compared to Temp Bond samples with an average of 8.6 ± 5.5%.ConclusionsGiven the results obtained in the present investigation the margin of CAD/CAM molar abutments should be located as coronally as possible to minimize the amount of cement remnants. If an epigingival or supragingival margin location is not feasible due to esthetic concerns, it cannot be recommended to place the margin of molar CAD/CAM abutments deeper than 1.5 mm in the proximal and oral regions.

Evaluation of Microleakage Using Different Luting Cements in Kedo Zirconia Crowns: An In Vitro Assessment

In Vitro Evaluation of the Effect of Different Luting Cements and Tooth Preparation Angle on the Microleakage of Zirconia Crowns

Effect of Machining Method and Margin Design on the Accuracy and Margin Quality of Monolithic Zirconia Crowns

Influence of luting agent on the microleakage of all-ceramic crowns

A comparative study of marginal microleakage and bond strength using three kinds of cements in zirconia all ceramic crown

An In Vitro Scanning Electronic Microscope Evaluation

Marginal, internal fit and microleakage of zirconia infrastructures: an in-vitro study

Influence of different cements and margin designs on marginal microleakage in metal crowns

An in Vitro Evaluation of Coronal Microleakage of Five Temporary Restorative Materials Used in Endodontic Access Cavities

Contrast study of microleakage incidence and extent of collocation uses of several clinical and frequently used cements and dowel materials

Contrast study of the microleakage of several clinical and frequently used cements and dowel materials

Effects of Different Removal Methods of Excess Resin Adhesive on the Microleakage of Alumina All-Ceramic Crowns

In Vitro Microleakage of Luting Cements and Core Materials

Evaluation of Cervical Margin Relocation for CAD/CAM Zirconia Crowns Using Different Composite Resin Materials and Cavity Designs: Marginal Gap and Microleakage

Evaluation of Marginal and Internal Adaptation of Crowns Fabricated with Three Different Zirconia CAD/CAM Materials

The Impact of Open versus Closed Computer-Aided Design/Computer-Aided Manufacturing Systems on the Marginal Gap of Zirconia-Reinforced Lithium Silicate Single Crowns Evaluated by Scanning Electron Microscopy: A Comparative In Vitro Study

Microleakage of new crown and fixed partial denture luting agents

Effect of different types of cements and the timing of tooth preparation on the coronal microleakage of fiber post

A Comparative Evaluation of the Bonding Strength, Marginal Adaptation, and Microleakage of Dental Cements in Prosthodontics: An In Vitro Comparative Study

Influence of margin location and luting material on the amount of undetected cement excess on CAD/CAM implant abutments and cement-retained zirconia crowns: an in-vitro study

Evaluation of the marginal adaptation and debonding strength of two types of CAD-CAM implant-supported cement-retained crowns