Abstract:With the growing demand for lightweight and high-performance components applied in extreme aerospace environments, there is a prospective interest in producing the integrated multi-material components consisting of titanium alloy and aluminum alloy. Laser powder bed fusion (LPBF), as a laser powder bed based additive manufacturing process with a high production flexibility, shows a promising potential in creating multi-material components. However, due to the possibility of the generation of various intermetallic compounds (IMCs) at the interface, it has been a significant challenge to fabricate reliable Ti/Al alloy multi-material components without any crack formation by LPBF. In this study, the Ti6Al4V/AlMgScZr multi-material parts were fabricated by LPBF and the effects of building parameters of AlMgScZr on the residual stress and crack control of Ti6Al4V/AlMgScZr multi-material parts were investigated. The evolution mechanisms of IMC phases at the interface under laser interaction were further revealed. Due to the change of elemental compositions and difference in Gibbs free energies of IMCs, a gradient ordered transition zone with a width of about 450 μm consisting of Al 3 Ti, TiAl, and Ti 3 Al was formed from AlMgScZr to Ti6Al4V. A finite element model was established to explain the effects of process parameters on residual stress evolution, cracking formation and its control. As the scan speed increased from 500 to 1100 mm/s and the attendant building height of AlMgScZr increased to 60 layers, the residual stress of laser processed Ti6Al4V decreased from 439 to 364 MPa, but the residual stress of AlMgScZr increased from 195 to 303 MPa. As the applied scan speed was enhanced to process AlMgScZr, the element diffusion was mitigated, thereby reducing the formation of IMCs and stress concentration. This study shows the possibility of in-situ control of IMCs and residual stress by process optimization during LPBF preparation of titanium alloy/aluminum multi-material parts without crack formation.

Residual stress analysis of TC4/Inconel718 functionally graded material produced by laser additive manufacturing based on progressive activation element method

Finite element analysis for residual stress of TC4/Inconel718 functionally gradient materials produced by laser additive manufacturing

Finite Element Simulation of Residual Stress in Laser Additive Manufactured Functionally Gradient Materials Based on Bessel Heat Source Model

Residual stress evaluation in innovative layer-level continuous functionally graded materials produced by Powder Bed Fusion-Laser Beam

Investigation of the Effect of Artificial Internal Defects on the Tensile Behavior of Laser Powder Bed Fusion 17–4 Stainless Steel Samples: Simultaneous Tensile Testing and X-Ray Computed Tomography

Analytical Modeling of Residual Stress in Laser Powder Bed Fusion Considering Part’s Boundary Condition

Effect of process optimization on laser additive manufacturing of Inconel 718 alloy based on finite element analysis: Thermal and structural evaluation

Thermomechanical Process Simulation and Experimental Verification for Laser Additive Manufacturing of Inconel®718.

Effect of residual stress on mechanical properties of Triply periodic minimal surface lattice structures in Additive manufacturing

Residual Stress Generation in Additive Manufacturing of Complex Lattice Geometries

Residual stresses and deformations of laser additive manufactured metal parts: a review

Influence of composition gradient variation on the microstructure and mechanical properties of 316 L/Inconel718 functionally graded material fabricated by laser additive manufacturing

The effects and utility of homogenization and thermodynamic modeling on microstructure and mechanical properties of SS316/IN718 functionally graded materials fabricated by laser-based directed energy deposition

Establishment and experimental verification of a three-dimensional finite element model for residual stress in surface processing of Inconel 718 alloy by laser cladding

In-situ control of residual stress and its distribution in a titanium alloy additively manufactured by laser powder bed fusion

Effect of Powder Layer Thickness on Residual Stress in Laser Powder Bed Fusion of IN718

Numerical investigation of residual stresses in thin-walled additively manufactured structures from selective laser melting

Residual Stress and Stress Corrosion of Alloy Materials in Laser Additive Manufacturing

The influence of building parameters on residual stress, interfacial structure, and cracking control of laser powder bed fusion processed Ti6Al4V/AlMgScZr multi-material parts

A functionally graded material design from stainless steel to Ni-based superalloy by laser metal deposition coupled with thermodynamic prediction

Residual Stress Mapping in Heat-Assisted Additive Manufacturing of IN 718: An X-Ray Diffraction Study