Abstract:Multi-laser powder bed fusion (PBF-MLB) is an advanced additive manufacturing (AM) technology, which can effectively improve the forming size and efficiency of components by increasing the number of lasers. However, the high residual stress generated by the repeated melting and solidification of the material in the overlap region under the action of multi-laser adversely affects formability during the PBF-MLB process. In this respect, this manuscript presents a stress control method based on the spatial and temporal differences in scanning strategies between dual-laser in PBF-MLB. A three-dimensional finite element model based on the sequentially coupled thermal-structural method was established to forecast the influence of these scanning strategies on the thermal history and residual stress distribution in both overlap and isolated regions. Meanwhile, the effective absorptivity of Ti-6Al-4V alloy powder was measured using a self-made calorimeter. The laser absorptivity of Ti-6Al-4V alloy powder was found to be 42.8% when P=170W and V=600mm/s, which was used in the simulation. The simulation results show that with the use of spatial difference scanning strategies (SDSC), the residual stress in the overlap region was greatly reduced by avoiding multiple synchronous remelting of the dual-laser. Meanwhile, after implementing temporal difference scanning strategies (TDSC) and spatial-temporal difference scanning strategies (S-TDSC), a lower temperature gradient was achieved compared to dual-laser synchronous scanning because only a single laser performs the processing. Therefore, the residual stress in the overlap region was significantly alleviated. Furthermore, the residual stress in the overlap region was lower with S-TDSC than with TDSC due to the more continuous thermal cycle created by the laser. In the inward symmetric scanning mode, the residual stress in the overlap region was reduced by 9.8% through using the SDSC compared to the base scanning strategy.

Residual Stress Mapping in Heat-Assisted Additive Manufacturing of IN 718: An X-Ray Diffraction Study

X-ray diffraction measurements and computational prediction of residual stress mitigation scanning strategies in powder bed fusion additive manufacturing

The residual stress in as-built Laser Powder Bed Fusion IN718 alloy as a consequence of the scanning strategy induced microstructure

Texture-based residual stress analysis of laser powder bed fused Inconel 718 parts

Effect of Powder Layer Thickness on Residual Stress in Laser Powder Bed Fusion of IN718

A study of the influence of novel scan strategies on residual stress and microstructure of L-shaped LPBF IN718 samples

Assessment of Residual Stresses in Laser Powder Bed Fusion Manufactured IN 625

Investigation of the Effect of Artificial Internal Defects on the Tensile Behavior of Laser Powder Bed Fusion 17–4 Stainless Steel Samples: Simultaneous Tensile Testing and X-Ray Computed Tomography

Laser Powder Bed Fusion of Inconel 718: Residual Stress Analysis Before and After Heat Treatment

Residual Stress Generation in Additive Manufacturing of Complex Lattice Geometries

Residual Strain Predictions for a Powder Bed Fusion Inconel 625 Single Cantilever Part

Analytical Modeling of Residual Stress in Laser Powder Bed Fusion Considering Part’s Boundary Condition

Effect of build orientations on residual stress, microstructure, and mechanical properties of additively manufactured alloy-718 components

Residual Stress Distribution in Selective Laser Melting of SS316L Parts

Residual Stress Analysis of Additive Manufactured A356.2 Aluminum Alloys using X-Ray Diffraction Methods

Diffraction-Based Residual Stress Characterization in Laser Additive Manufacturing of Metals

Thermomechanical process modelling and simulation for additive manufacturing of nanoparticle dispersed Inconel 718 alloys

Knowledge of process-structure-property relationships to engineer better heat treatments for laser powder bed fusion additive manufactured Inconel 718

Understanding processing parameters affecting residual stress in selective laser melting of Inconel 718 through numerical modeling

In-situ control of residual stress and its distribution in a titanium alloy additively manufactured by laser powder bed fusion

Numerical Analysis of the Effect of the Spatial and Temporal Scanning Strategies on the Residual Stress in the Multi-Laser Powder Bed Fusion of Ti-6Al-4V