Abstract:Statement of problem. Selective laser melting (SLM) technology has been introduced to fabricate dental restorations. However, the fit of these restorations still needs further study.Purpose. The purpose of this in vivo investigation was to compare the marginal and internal fit of SLM metal ceramic crowns with 2 lost-wax cast metal ceramic crowns and to evaluate the influence of tooth type on the marginal and internal fit of these crowns.Material and methods. A total of 330 metal ceramic crowns were evaluated. The metal copings were fabricated with SLM Co-Cr, cast Au-Pt, and cast Co-Cr alloy (n=110). The marginal and internal gaps of crowns were recorded by using a replica technique. The anterior and premolar replicas were sectioned 2 times, and molar replicas were sectioned 4 times. The marginal and internal gap width of each cross section was examined by stereomicroscope at x30 magnification. Two-way analysis of variance was performed to identify the statistical difference among the groups.Results. The marginal fit of the SLM Co-Cr group (75.6 +/- 32.6 mu m) was not different from the cast Au-Pt group (76.8 +/- 32.1 mu m) (P>.05) but was better than the cast Co-Cr group (91.0 +/- 36.3 mu m) (P<.01). No significant difference was found among the SLM Co-Cr group (127.3 +/- 45.8 mu m), cast Au-Pt group (129.9 +/- 61.1 mu m). and cast Co-Cr group (142.5 +/- 63.7 mu m) (P>.05). The mean occlusal gap width of the SLM Co-Cr group (309.8 +/- 106.6 mu m) was significantly higher than that of the cast Au-Pt group (254.6 +/- 109.6 mu m) and the cast Co-Cr group (249.6 +/- 110.4 mu m) (P<.005). No significant difference was found in the marginal fit among the anterior group (84.4 +/- 35.1 mu m), the premolar group (80.6 +/- 26.3 mu m), and the molar group (82.7 +/- 38.0 +/- m) (P>.05). Also, no significant difference was found in the axial fit among the anterior group (138.3 +/- 52.5 mu m), the premolar group (132.9 +/- 50.4 mu m), and the molar group (134.4 +/- 52.5 mu m) (P>.05). The anterior group (267.6 +/- 110.2 mu m) did not differ from the premolar group (270.2 +/- 112.8 mu m) and the molar group (268.6 +/- 110.5 mu m) in occlusal fit (P>.05).Conclusions. The marginal fit of SLM Co-Cr metal ceramic crowns was similar to that of the cast Au-Pt metal ceramic crowns and was better than that of the cast Co-Cr metal ceramic crowns. The SLM Co-Cr metal ceramic crowns were not significantly different from the 2 cast metal ceramic crowns in axial fit but were less accurate in occlusal fit. Tooth type did not influence the marginal and internal fit of the metal ceramic crowns.

Fit comparison of interim crowns manufactured with open and proprietary 3D printing modes versus milling technology: An in vitro study

Evaluation of the marginal and internal fit of a single crown fabricated based on a three-dimensional printed model

Comparison of the internal fit of metal crowns fabricated by traditional casting, computer numerical control milling, and three-dimensional printing

In Vitro Comparison of Internal and Marginal Adaptation between Printed and Milled Onlays

Comparison of Intaglio Surface Trueness of Interim Dental Crowns Fabricated with SLA 3D Printing, DLP 3D Printing, and Milling Technologies

Comparing the accuracy of crown fitting between milling and 3D printing techniques using CAD/CAM technologies

Clinical Marginal and Internal Fit of Crowns Fabricated Using Different CAD/CAM Technologies

Marginal Fit, Mechanical Properties, and Esthetic Outcomes of CAD/CAM Interim Fixed Dental Prostheses (FDPs): A Systematic Review

Evaluation of fracture resistance and marginal fit of implant-supported interim crowns fabricated by conventional, additive and subtractive methods

Accuracy and adaptation of one-piece endodontic crowns fabricated through 3D printing and milling

Surface trueness and precision of interim restorations fabricated by digital light processing and CAD-CAM milling systems

Evaluation of Accuracy of Different Print Angulations for 3D Printed Dental Crowns

Surface roughness and marginal adaptation of stereolithography versus digital light processing three-dimensional printed resins: An in-vitro study

Comparison of surface roughness of additively manufactured implant-supported interim crowns fabricated with different print orientations

Fit of removable partial denture frameworks fabricated from 3D printed patterns versus the conventional method: An in vitro comparison

3D-printed versus conventionally milled zirconia for dental clinical applications: Trueness, precision, accuracy, biological and esthetic aspects.

Comparison of wear and marginal fitness of 3D-printed deciduous molar crowns: An in vitro study

Clinical Marginal and Internal Fit of Metal Ceramic Crowns Fabricated with a Selective Laser Melting Technology.

An in vitro comparison of the marginal fit of provisional crowns using the virtual tooth preparation workflow against the traditional technique

Effect of three-dimensional print angle on integrity of interim crowns: A systematic review

Effect of build orientation on the fracture resistance and marginal quality of 3D-printed anatomic provisional crowns: An in-vitro study