Abstract:The most critical condition for performing Dynamic Nuclear Polarization (DNP) NMR experiments is achieving sufficiently high electronic B1e fields over the sample at the matched EPR frequencies, which for modern high-resolution NMR instruments fall into the millimeter wave (mmW) range. Typically, mmWs are generated by powerful gyrotrons and/or extended interaction klystrons (EIKs) sources and then focused onto the sample by dielectric lenses. However, further development of DNP methods including new DNP pulse sequences may require B1e fields higher than one could achieve with the current mmW technology. In order to address the challenge of significantly enhancing the mmW field at the sample, we have constructed and tested one-dimensional photonic band-gap (PBG) mmW resonator that was incorporated inside a double-tuned radiofrequency (rf) NMR saddle coil. The photonic crystal is formed by stacking ceramic discs with alternating high and low dielectric constants and thicknesses of λ/4 or 3λ/4, where λ is the wavelength of the incident mmW field in the corresponding dielectric material. When the mmW frequency is within the band gap of the photonic crystal, a defect created in the middle of the crystal confines the mmW energy, thus forming a resonant structure. An aluminum mirror in the middle of the defect has been used to substitute one-half of the structure with its mirror image in order to reduce the resonator size and simplify its tuning. The latter is achieved by adjusting the width of the defect by moving the aluminum mirror with respect to the dielectric stack using a gear mechanism. The 1D PBG resonator was the key element for constructing a multi-resonant integrated DNP/NMR probehead operating at 190-199 GHz EPR/300 MHz 1H/75.5 MHz 13C NMR frequencies. Initial tests of the multi-resonant DNP/NMR probehead were carried out using a quasioptical mmW bridge and a Bruker Biospin Avance II spectrometer equipped with a standard Bruker 7 T wide-bore 89 mm magnet parked at 300.13 MHz 1H NMR frequency. The mmW bridge built with all solid-state active components allows for the frequency tuning between ca. 190 and ca. 199 GHz with the output power up to 27 dBm (0.5 W) at 192 GHz and up to 23 dBm (0.2 W) at 197.5 GHz. Room temperature DNP experiments with a synthetic single crystal high-pressure high-temperature (HPHT) diamond (0.3 × 0.3 × 3.0 mm3) demonstrated dramatic 1500-fold enhancement of 13C natural abundance NMR signal at full incident mmW power. Significant 13C DNP enhancement (of about 90) have been obtained at incident mmW powers of as low as <100 μW. Further tests of the resonator performance have been carried out with a thin (ca. 100 μm thickness) composite polystyrene-microdiamond film by controlling the average mmW power at the optimal DNP conditions via a gated mode of operation. From these experiments, the PBG resonator with loaded Q ≃ 250 and finesse F≈75 provides up to 12-fold or 11 db gain in the average mmW power vs. the non-resonant probehead configuration employing only a reflective mirror.

Exploration of Materials for Three-Dimensional NMR Microcoil Production via CNC Micromilling and Laser Etching

5-Axis CNC Micromilling for Rapid, Cheap, and Background-Free NMR Microcoils

Evaluation of double-tuned single-sided planar microcoils for the analysis of small 13 C enriched biological samples using 1 H-13 C 2D heteronuclear correlation NMR spectroscopy

The design and fabrication of a low-field NMR probe based on a multilayer planar microcoil

3D printed microchannels for sub-nL NMR spectroscopy

Low-field NMR Micro Coils Based on Printed Circuit Board Technology

MEMS micro-coils for magnetic neurostimulation

A Cryogenic Tune and Match Circuit for Magnetic Resonance Microscopy at 15.2T

Digital Microfluidics and Nuclear Magnetic Resonance Spectroscopy for in Situ Diffusion Measurements and Reaction Monitoring.

A complete 3D-printed tool kit for Solid-State NMR sample and rotor handling

3D-Printed Integrative Probeheads for Magnetic Resonance

Multinuclear nanoliter one-dimensional and two-dimensional NMR spectroscopy with a single non-resonant microcoil

Fabricated on the capillary surface by cylindrical projection lithography for nmr application

Design of an Innovative Downhole NMR Scanning Probe

A practical multinuclear transceiver volume coil for in vivo MRI/MRS at 7 T.

High-resolution, high-sensitivity NMR of nanolitre anisotropic samples by coil spinning

A Compact Planar Triple-Nuclear Coil for Small Animal 1H, 13C, and 31P Metabolic MR Imaging at 14.1 T

Long nanomechanical resonators with circular cross-section

A Novel Metamaterial-Inspired RF-coil for Preclinical Dual-Nuclei MRI

Multi-resonant photonic band-gap/saddle coil DNP probehead for static solid state NMR of microliter volume samples

Bio-inspired surface coil for small-bore MRI at 15.2 T