Abstract:Bi2Te3-based compounds are currently the most commercially relevant thermoelectric materials near room temperature. They are prepared via hot pressing, hot deformation, spark plasma sintering, and other consolidation processes, which are typically performed at 400-500 degrees C. Such high-temperature processes are energy-intensive and generate unnecessary waste heat, making them undesirable for a large- scale production. In this study, a low-temperature liquid-phase-assisted sintering (or so-called cold-sintering) process was employed to fabricate p-type Bi0.5Sb1.5Te3 bulk materials at temperatures below 150 degrees C. At the optimal sintering temperature (130 degrees C), a ZT value as high as 0.56 at 450 K can be achieved, competitive to that of a commercial Bi0.5Sb1.5Te3 ingot (ZT 0.8-1.0). The addition of a small amount of transient liquid facilitates grain reorientation and expedites a mass transfer process under axial compaction and liquid evaporation conditions, thus resulting in nearly fully densified Bi0.5Sb1.6Te3 pellet samples (>97% theoretical density). Furthermore, the low-temperature sintering process results in the reduction of grain size and promotes twin boundaries, resulting in a low lattice thermal conductivity of 0.57 W m(-1) K-1 at 380 K due to phonon scattering. The strategy reported in this work can be used not only as a substitute for high-temperature sintering of other thermoelectric materials but also to engineer phonon scattering for high-performance thermoelectrics.

Approaching crystal's limit of thermoelectrics by nano-sintering-aid at grain boundaries

Approaching Crystal’s Limit of Thermoelectrics by Nano-Sintering-aid at Grain Boundaries

Grain Boundary Engineering for Achieving High Thermoelectric Performance in N‐type Skutterudites

Realizing High-Performance Thermoelectric Power Generation Through Grain Boundary Engineering of Skutterudite-Based Nanocomposites

Dramatic Enhancement of Thermoelectric Performance in PbTe by Unconventional Grain Shrinking in Sintering Process

Enhancing the room temperature thermoelectric performance of n-type Bismuth-telluride-based polycrystalline materials by low-angle grain boundaries

Highly Distorted Grain Boundary with an Enhanced Carrier/Phonon Segregation Effect Facilitates High-Performance Thermoelectric Materials

Effective Atomic Interface Engineering in Bi2Te2.7Se0.3 Thermoelectric Material by Atomic-Layer-deposition Approach

Dramatic Enhancement of Thermoelectric Performance in PbTe by Unconventional Grain Shrinking in the Sintering Process

Improved figure of merit (z) at low temperatures for superior thermoelectric cooling in Mg3(Bi,Sb)2

Improving the Performance of Thermoelectric Materials by Atomic Layer Deposition-based Grain Boundary Engineering

Enhancement of thermoelectric performance in Mg 3 (Sb,Bi) 2 through engineered lattice strain and controlled carrier scattering

Enhancement of Thermoelectric Performance in Mg3(Sb,Bi)2 Through Engineered Lattice Strain and Controlled Carrier Scattering

Cold-Sintered Bi2Te3-Based Materials for Engineering Nanograined Thermoelectrics

Excellent thermoelectric performance of boron-doped n-type Mg3Sb2-based materials via the manipulation of grain boundary scattering and control of Mg content

Enhancing thermoelectric performance of AB 2 Sb 2 -type Zintl phase through band shaping and lattice distortion

Enhancing Thermoelectric Performance of AB2Sb2-type Zintl Phase Through Band Shaping and Lattice Distortion

Dopant-segregation to grain boundaries controls electrical conductivity of n-type NbCo(Pt)Sn half-Heusler alloy mediating thermoelectric performance

All‐Inorganic Nanocrystals As a Glue for BiSbTe Grains: Design of Interfaces in Mesostructured Thermoelectric Materials

Simultaneous Optimization of Electrical and Thermal Transport Properties of Bi0.5sb1.5te3 Thermoelectric Alloy by Twin Boundary Engineering

Enhanced thermoelectric figure of merit in polycrystalline carbon nanostructures